Search results

I recently purchased a quick hitch adapter for the back of my Kubota L3301 and overall I’m very happy with it. the issue I’ve run into is the items that have the shorter PTO shafts (chipper & tiller) don’t have enough shaft overlap to run safely. Looking around on the internet for replacement...

I have a Woodland Mills chipper on the way and I’m wondering how to engage the PTO then dismount to feed the chipper. If I remember correctly, the seat safety switch will kill the engine once the weight comes off.

I’ve recently some logging done on my 30 acre lot. I’d like to buy a PTO driven chipper for clean up. Recommendations? It‘ll be strapped to an L3301. thanks

Hi all, I recently added a third function valve to my tractor and was wondering where I could go in town to pick up some type of protective sleeve I could slide the two new hoses into for protection. I see stuff on line, but I was hoping that maybe someone has seen what I need in a big box store...

I just mounted a SS Quick Attach adapter to the front end of my L3301 to use a grapple. I’d still like to be able to use a bucket for moving material, so now I need a compatible bucket. Any suggestions on what brands to look at or what to stay away from? thanks

Id like to adjust the travel on the hydraulic cylinders the curl/dumps the loader bucket. I would like to take just a little bit of the curl out. is that possible?

Just finished up adding a quick hitch adapter to the tractor. Went very smooth. Now I just need for the third function kit to show up so I can start using this grapple. After I get that done, I need to have the new mounting plate for the loader bucket welded on so I can use that with the adapter.

Morning, im in the preliminary steps of replacing my pin on FEL with a quick attach adapter. im wondering if the bolts that hold the bucket pins in place are a one time use and replace, or if they can be reused. is there a torq spec? thanks, steve

I’m doing the 400 hr service on my L3301 and I can get the fuel filter to break loose. applying pressure with a filter wrench is twisting the mount, I’m afraid I’ll break it. Any advice?

Anyone know why Kubota quit making the QH15 quick hitch attachment? any recommended replacevents? thanks Steve

I seems to me that the shield around the slip clutch on my RCF2060 mower is worthless, other than keeping law suits at bay. Trying to service that U joint or do a slippage check at the beginning of the season is a pain in the a$$ with that shield in place. Im removing it unless there’s a...

Hello all, I’ve developed a leak on the hose marked in red that goes from the control valve to the loader. when I look it up on a parts diagram, there are three different part Numbers for the hose. How do I determine which is the hose I would need? L3301HST LA525 loader

Hello all, I need to change the coolant on my L3301. Im having trouble getting the hood up high enough to pour the new coolant into the radiator fill neck. Do I need to remove the hood or am I missing a latch somewhere to get the hood to raise up and out of the way? As it is now, my hood will...

Hi, ive got a single bottom plow that normally just sits in a pile until I need it, then it’s like wrestling a greased pig to get it up at Dogwood attached to the lift pins. Anyone have any good ideas on how to store it so I can just back up to it to attach?

Hello all, im thinking of removing the shield that is mounted over the top half of my PTO shaft. it seems to be a huge hinderance when getting a driveshaft attached or disconnected. Any reason why this would be a bad idea?

Hello all,I need to drain and flush my radiator, but cannot figure out what to use to remove the drain plug. It’s a plastic plug that looks like it takes an extremely wide and nearly flat Phillips. I’m afraid that if I use a large flat tip screw driver I’ll crack the plug. Steve

Hello all, I’ve been looking at filter prices for an upcoming service and noticed one of the hydraulic filters for my L 3301HST is $46. P/N is HH3A0-82623. The Wix equivalent filter WL10043 is half that price at O’Reillys. Anyone have any experience, good or bad, with Wix filters? I’ve never...

Hello all, Was wondering if my one knew of where I might locate a list of part numbers for common service items such as fuel, oil and hydraulic filters for my L3301HST. TIA Steve

Would someone please explain to me what different series driveline shafts are? I need to replace the outer shaft of the driveline that came with my FDR1672, I’m looking on agri supply but have no idea what series the shaft is that I need. Thanks Steve

Hello all. Yesterday while using the tractor and FEL I ‘felt’ a pop and immediately noticed a lot of slop in the control for moving the FEL up and down. I noticed that this stop bolt was no longer attached to the FEL bracket. I have two questions: 1. how do I remove the plastic FEL control...