Search results

Hi everyone, When I’m in low on my L3200 HST it “seems” to have the correct power. However, when I put it in high speed to travel down the road it does not go to top speed. Instead it bogs down almost like it’s cutting out when accelerating. Release pedal and returns to high idle but in what...

Hi everybody. I have an issue with leaking hydraulic tank fittings. First, the reason it’s leaking I’ve discovered is the fact that the drain plug to the tank, (which is plastic), is stripped. So, in less words, when I turn the plug “out” it only spins and spins. Not spinning freely but I can...

Has anyone ever done or seen this done? I’m looking to possibly mount a quick attach off a 3 point for picking up heavy boulders and rocks. Is this possible? I’d think anything is, but I have yet to see it.... I see where there is a “mechanism” that allows for quick”er” attaching, but not the...

Here’s another forst for me,.... working with tractor backing up in woods and it’s like it’s “locked” in reverse. Pedal is hard as a rock. Can’t move it. Can anyone help me? No sticks jammed in linkage as I looked on right hand side below pedal linkage and it’s clear. Thank you in advance!!

I’m hoping to find a good heavy duty trailer for hauling rocks and boulders. I’ve searched here on the forums but they cover mainly road worthy trailers. I’m looking for a trailer that would handle on average 2’-3’ boulders being put into it and then “hopefully” dumped for unloading. It’d have...

I had replaced the tie rod ends on my 2015 L3200 HST about 2 years ago. All was fine. Broke one a week ago. Local Kubota Parts Person tells me I need this one on the left side as in picture. However, I have it on the opposite side already. Does it matter? I know one side should have the solid...

Searched this one up and haven’t found it. What is your advice on using forks to work the earth/ground to loosen up to be able to better utilize a grapple to pick up the stumps and rocks/boulders afterwards? Would it be too much on the unit due to the possible spring tgey May have? I have an...

Don’t know why this is doing this. Looks like the grapple or bucket may have been connected to only one side of the quick connect under heavy load. Happened early on but nothing recently. How would one go about correcting this? Blocks of wood under the crooked piece, little by little till it is...

Can anyone tell me what brand of grapple this is and what it might be worth? Currently priced @ $750. Thank you

Can anyone tell me a dealers name for snatch blocks that's closer to Michigan besides Baileys? Thank you! Chris

Hi again to all!! I have big boulders that I'm hoping to loosen up/pill up with my 3 point. I just don't know if an attachment exist for such an application. The thing that comes to mind is a "Ripper" like is used on the BIG DOZERS of Gold Rush. I understand total different application as far...

Updated with Video: Tilt Not Working Properly! Please Help!! When I'm at regular rpm and am tilting the grapple by pulling joystick all the way to the left, it travels as it would normally until it gets about 5/8 thru to the top. Then, it slows down real slow, and then picks up speed just...

What Causes A Cable to Do This? (Pictures Added) Hi guys, I'm wondering if you can tell me why this cable is doing this? It's 3/8" 140' long. I had lost the pin from one of my cinch blocks. I couldn't get another one, so instead I used one of these, due to the fact the color was better so I...

The manual says 14-77 degrees use sae20, sae10w-30, or 15w-40. Is there one that's better than the other?

I'm in the process of pulling big cedar trees out of the woods. I was using the rear blade with a chain wrapped around it & the log. This was working ok, but wasn't the surest way of knowing if have lift on the but end of the log. As if start moving out the log would normally end up dragging at...

I'm trying to find out where I can go online to see an illustrated parts list for my B2551 Blower. It's not listed on kubota parts.com. Thank You ! Chris

I'm trying to get my back blade to dig in a bit more. What do you suggest for weight? I have a nice newish/shiny back blade. With that said, I realize pretty doesn't equal practical. I'm looking at mounting my chainsaw on it as well. Unless the weight won't allow enough room. Any advice would...

Update: Sept 12; Land Pride SGC1060 Welds Ripping!! I have just purchased this grapple along with my tractor.. I have 34 hours on the tractor. Of it, about 31 hours with the grapple being used. Im clearing a road thru my property, moving trees, logs, stumps, (not many stumps, but about 4 decent...

My projects are progressing well. The grapple is working super. The one I have is perfect for what I am doing. It gets everything I throw at it done. The only thing I need to do is try to figure out how to fabricate a rock sifter for the approximately 8" rocks and under that go thru the grapple...

Ok. I have everything I need for the hydraulic cylinder I've attached to a small Trailor. The only thing I'm lacking, (and don't know the name of), are the plate that the hydraulic hoses go thru with the 2 fittings on. I guess it's used to hold both hoses in a fixed position; the same as on my...