Search results

This is a rebuildable 3 cylinder diesel plus misc parts left over from replacing the engine in a Kubota B7100 HST tractor. Engine was running when removed, no knocks just allot of blow-by, leaks and burning oil. Engine is complete with the exception of the hydraulic pump. Dynamo is included but...

Any reason not to leave the fuel shut-off on all the time on a B7100? I never shut the fuel off on my Fords but the guy I bought the 7100 from made it a point to show me the fuel shut-off and said to always shut it off when it is parked. Twice now I have ran it out of fuel by forgetting to turn...

Would anyone be willing to explain or show me how the factory routs the headlight wire on a B7100 HST? Can't believe it just hangs over the radiator Like it does on the one I have. Thanks

On the down side of the B7100 HST resurrection and getting ready to find a home for what I have left over. Have a complete engine less hydraulic pump that was running when removed. No knocks just lots of blow by, Muffler, Starter, Radiator and a few misc parts. Thinking of listing it all as one...

Seems like everything I look at on this tractor needs attention. Removed the mid PTO shaft and discovered one of the U-Joints feels like it has gravel in it. Looked up the part number 76539-31180 and checked price. Just can't in my right mind pay $100.00 for a danged old U-joint. Has anyone...

Discovered someone in it's past went gorilla on the bolts that hold the mid mount mower on my B7100. 3 bolts on each side for the front brackets to tractor frame. Most are now stripped 10mm welded nuts on the inside of a box. Near impossible to get to the back side to weld new nuts on. Did that...

After seeing some recommend Coleman on the forum thought I would give them a shot at 3 items I needed for the B7100 I am resurrecting. Bottom line... I ended up canceling the Coleman order and just now reordered from Messick's. Placed the order on Monday the 17th, they charged my CC on the 18th...

I have two complete air filter assemblies from different generations of the B7100 and both have an issue with the bottom spring wire latch not latching properly. The top one on both seem fine, lock in with plenty of tension but the bottom seems like it isn't catching properly and hits the cover...

Know what happens when you change an oil filter and do not notice the old gasket didn't come off with the filter. You start the engine and create the biggest mess possible. Oil hits the fan which covers you and everything else in the shop then proceeds to dump 3 quarts of oil on your shop floor...

Wow! Tension pulley 76539-34883, $101.27 plus shipping from Messick's. Anyone know of a less expensive solution?

Took me a while, I'm old and wok slow but the 7100 I bought with a spare engine is now running. Sounds great, starts easy, no blow by or smoke. Haven put the tin back on it yet still have a few minor items I want to address, couple injectors are leaking and idle needs adjusting. Allot of work...

Nuther question. Keep reading about the radiator overflow whistle and wondering what/where it might be. Both radiators I have just have a tube routed down the side of the radiator to vent the overflow to the ground and what look like standard radiator caps. What is it that makes it whistle?

Swapping a first generation motor into a 2nd generation tractor. Older motor has a 3 wire dyno existing motor has a 2 wire dyno. Thinking the regulator and wiring must go with the existing dyno right? Managed to get the dyno off the existing motor using a gear wrench on that lower middle nut...

This is the B7100 HST I just bought along with the spare motor. Have $2500.00 in it so far. Also have the MM 60 inch deck, removed for transportation. The existing motor has allot of blow by, is hard to start and uses oil. The 2nd motor is suppose to be in good condition, PO said he heard and...

Picture shows the existing speed control linkage that came on my B7100 HST. Looking at the parts diagram I am missing what Kubota is calling a Turnbuckle. Also I do not believe the top rod should be bent like it is. What has me wondering is neither rod has a left hand thread and they are...

My new to me B7100 HST 4WD is going to need tires, I have followed all the posts and links round and round and am confused as ever about exactly what is available. I bought this tractor specifically because it had turf tires. If I need to tear up the lawn I have two 5000 pound Fords with AG...

An old Ford guy (3000 and 3600) that needed something with turf tires. Found a Kubota B7100 HST 4 wheel drive with a bad motor along with a good motor. It will run but is hard to start and has allot of blow-by. Was told good motor came out of a low hour B7100 with a bad transmission, had to take...