Search results

If it’s just the boot that’s torn, tractor supply sells a boot kit.

Thanks everyone.

I went to tractor supply and picked up a pair of pioneer 2 way couplers and 2 1/2 inch hoses to bridge the gap between the plow hoses and 3rd function valve on loader. The issue is, after I got home I noticed that the plow hose is 3/8 inch. If I get hydraulic fittings to connect the 3/8 plow...

Thanks everyone. So it really doesn’t matter if the male end is on the tractor or the plow so long as the other side has the opposite ?

Thanks. Does the male end go on the loader and the female end on the plow?

I have a B26. I just got a 3rd function valve for my loader installed by the dealer and a hla 1000 plow. The valve has block off caps at this time. The plow came with two small hoses that are also blocked off with caps. I need another foot or so to make the connection along with a coupler. I am...

Thanks for the responses. I’ll probably pass on it. It’s not good enough deal to take the risk of it not working and having to resell it. I’ll probably just go with a landpride or blue diamond one which are more manageable at around 550lbs.

Loader specs at 500mm forward is: 946 lbs.

The machine can lift about 1300 but it only weighs 4000. It can lift it but I’m concerned it might be too front heavy to push big snow even with chains. Pic is taken from tractor data.

I have a B26 TLB. I am looking at a 72 inch plow made for a skid steer. It weighs about 750 pounds, and is a good deal. I am a bit concerned over the weight of the plow as it may be a bit much for my machine to push with heavy snow. I am planning on getting chains for rear tires. Please let me...

I attempted to free up the ball bearings but have been unsuccessful. They do not want to move at all with a screw driver. I even tried a sledge hammer to get the shaft onto the tractor however it continues to get hung up apparently on the ball bearings. Is it possible to just swap out the End...

Thanks for the responses. Jblac, that is a good point. I will check for imperfections. I only have one PTO shaft, which has the ball bearings. I am going to keep using PB blaster, bc they might be stuck. Wingnut, the shaft extends and has enough play to make the connection. My issue is with...

Hello. I purchased a 60 inch used snow blower that came with PTO shaft. I have a 2007 B26. They guy who I bought the blower off of had a 35 HP John Deere. I am having difficulty getting the PTO shaft to securely hook up to my tractor. The PTO shaft goes over the splines of my B26 PTO but the...

I like it a lot. The machine is a beast. I dug up a bunch of stumps. Pound for pound, your going to have a hard time finding a stronger machine. I got the thumb for it which is a great addition.

Seems like a good deal. I picked up a mint 2007 last year with 350 hours for 23500$

Thanks. For some reason I cannot find the specific hydraulic lines I need on that site. I am thinking of removing both hoses, capping the lines and get the hoses made by this hydraulic business near my home. By any chance, does anyone know the size of fittings I need to cap the lines?

I purchased a used 2007 B26 TLB last fall. I put about 50 hours on it without issue. Unfortunately today I used it to move some rocks and I noticed the left side loader hydraulic line is leaking. It appears to be dry rotted a bit. It's leaking right where the foot step is. The line is inside the...

I added a hydraulic thumb kit to my B26. It was a pretty easy job. Can't wait to get to actually use it.

The hoe is already plumbed from the factory and also came with the foot pedal. The only thing I need to add is the actual thumb and cylinder, which has 2 small hoses.

I just picked up a B26 thumb kit. The instructions that came with the kit aren't the best. Should I put the bucket on the ground and disconnect the Hydralic lines of the backhoe from the machine before attaching the thumb lines? Any recommendations would be much appreciated.