Sod Cutter

BXHoosier

Well-known member

Equipment
BX24
Jan 21, 2018
453
506
93
Indiana
This year, I’ll be re-grading the yard to help water drain away from the house and off of the paved driveway. A new 90’ path from the deck to the patio is also in the plans. I’m building a simple sod cutter to remove the grass and hopefully re-lay it after I remove some dirt to fix the grade.

The plan is for the cutter to attach to my 3PH fork/ trailer mover frame. It will cut 2”
deep by 20” wide. The depth gauge roller is made from 2” pipe with steel slugs pressed into the ends that runs on a 1” shaft that can be greased. Making those pieces gave me the chance to try out the homemade steady rest on my lathe and the press I built.
20616607-8043-447C-B030-823BD35CF0F9.jpeg
F0FEF7C1-A65A-474E-A14E-7B352C024D71.jpeg
D3991EC1-82E7-4A8D-96B8-118857BCF503.jpeg
1CCAE976-4CBE-4784-AE77-2821F18C6403.jpeg
 
  • Like
Reactions: 3 users

Motion

Well-known member
Lifetime Member

Equipment
Kubota MX5100HST/FEL
Aug 17, 2020
518
285
63
Mandeville Louisiana
Looking good, I suggest adding two 8 inch discs with sharpened edges to the end of the axle to cut the sod at the sides. Will the blade be square to the sod or on a skew? Ensure there's enough room for the sod to pass through the uprights carrying the assembly. Will you need weights to keep the roller buried? Adjustable guide wheels might be better than the roller mounted outboard the discs. Angling the blade will allow for digging in, with the guide wheels holding back.
 

Runs With Scissors

Well-known member

Equipment
L2501 TLB , Grappel, Brush Hog, Box Blade, Ballast box, Forks, Tiller, PH digger
Jan 25, 2023
1,722
1,823
113
Michigan
Nice job so far.

I like that press and steady rest. I have been meaning to make a steady rest that has bearings. Does yours have bearings that the part rides on?


Paul
 

GreensvilleJay

Well-known member

Equipment
BX23-S,57 A-C D-14,58 A-C D-14, 57 A-C D-14,tiller,cults,Millcreek 25G spreader,
Apr 2, 2019
9,670
3,916
113
Greensville,Ontario,Canada
It's nice to see someone MAKE stuff !! Just wondering if you're making a BIG sod roll carrier cause 90' of sod will become a HUGE roll !;)
I'm going to 'borrow' your press on wheels.THAT is a great idea ! It'll allow me to see what's hidden behind the press for 32 years......
cheers
 

BXHoosier

Well-known member

Equipment
BX24
Jan 21, 2018
453
506
93
Indiana
The roller will be a few inches forward of the blade to control the cutting depth. The blade will be tilted down 10 degrees to help it pull down under the sod and the cutting edge will be beveled to a sharper angle. The vertical plates will be sharpened too. It will be similar to this Ventrac sod cutter without the adjustment on the depth roller.

8DBB5A0F-511B-4421-8B36-DDE52FC1CB69.jpeg

My lathe steady rest did have bearings when it was originally made, but when I bought the lathe, two of the three guides were missing, so I remade the guides and used bronze to make the tips.
 

BXHoosier

Well-known member

Equipment
BX24
Jan 21, 2018
453
506
93
Indiana
I’m certain it will need weight to get it to cut in. The plan is to mount the cutter to my 3PH fork frame and add weight to a receiver hitch cargo carrier slid into the 2” receiver on my frame.
 

BXHoosier

Well-known member

Equipment
BX24
Jan 21, 2018
453
506
93
Indiana
Welded it together today. Now, to figure out how I’m going to mount it to my 3PH frame. I also need to grind a sharper angle on the blade.
76A49DFB-F657-475D-B309-2A9FA8548FAF.jpeg
A4A4564D-DCCF-4BB9-BBBF-1DB98CC1069F.jpeg
 

RCW

Well-known member
Lifetime Member

Equipment
BX2360, FEL, MMM, BX2750D snowblower. 1953 Minneapolis Moline ZAU
Apr 28, 2013
8,282
3,866
113
Chenango County, NY
Hoosier - - I'm following your thread closely.

Have zero need for a sod cutter....just enjoy the ingenuity and skills of OTT members. (y)

At my house it would be a weed cutter......😝
 
  • Like
Reactions: 1 user

Lil Foot

Well-known member
Lifetime Member

Equipment
1979 B7100DT Gear, Nissan Hanix N150-2 Excavator
May 19, 2011
7,259
2,203
113
Peoria, AZ
This year, I’ll be re-grading the yard to help water drain away from the house and off of the paved driveway. A new 90’ path from the deck to the patio is also in the plans. I’m building a simple sod cutter to remove the grass and hopefully re-lay it after I remove some dirt to fix the grade.

The plan is for the cutter to attach to my 3PH fork/ trailer mover frame. It will cut 2”
deep by 20” wide. The depth gauge roller is made from 2” pipe with steel slugs pressed into the ends that runs on a 1” shaft that can be greased. Making those pieces gave me the chance to try out the homemade steady rest on my lathe and the press I built. View attachment 97918 View attachment 97919 View attachment 97920 View attachment 97921
Who says you can't do big stuff on a small lathe? (y)
 
  • Like
Reactions: 1 users

BXHoosier

Well-known member

Equipment
BX24
Jan 21, 2018
453
506
93
Indiana
Mocked up the cutter on my 3PH frame to figure out how and where to mount it. The plan is to offset it so that it runs even with the side of the loader bucket so that the bucket can be used as a guide. The mount will also be symmetrical so that it can be used on either the right or left side.

C54AD39E-A54D-4171-9581-A40C0CA34BEA.jpeg
7CCEABDB-AB0A-4F45-9FD2-4BBADED5DB2E.jpeg
 

North Idaho Wolfman

Moderator
Staff member
Lifetime Member

Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
Jun 9, 2013
28,286
4,853
113
Sandpoint, ID
Could just put a male reciver on it and attach it right to the reciver hitch?
Yea I know it would be right in the center.
Doing that, you could hinge it in the rear and have an adjustment cam (like the top link) in the front to get the right angle for the culler blade and roller engagement.
 

bird dogger

Well-known member
Vendor Member

Equipment
Kubota B2650 and lots of other equipment
Feb 24, 2019
1,569
1,409
113
North Dakota
Title and post #1 says a "Sod Cutter" as in lawn grass.
But it could also double as a "Bulk Velveeta Cheese Slicer"!! :ROFLMAO:
 

BXHoosier

Well-known member

Equipment
BX24
Jan 21, 2018
453
506
93
Indiana
The sod cutter works really well. I used it yesterday to remove a strip of sod 40” wide by 90’ long where I’m putting in a new paver path from the deck out to the barn. I put my hitch carrier on the frame and added 360 lbs of sandbags to help get the cutter into the dry, rock-hard ground. It took a little adjustment to the turnbuckle on the RH 3-point lift link to get it to cut level.

991E374D-0950-48C4-B8AF-45EEACB62A1A.jpeg
 
  • Like
Reactions: 1 users

bird dogger

Well-known member
Vendor Member

Equipment
Kubota B2650 and lots of other equipment
Feb 24, 2019
1,569
1,409
113
North Dakota
The sod cutter works really well. I used it yesterday to remove a strip of sod 40” wide by 90’ long where I’m putting in a new paver path from the deck out to the barn. I put my hitch carrier on the frame and added 360 lbs of sandbags to help get the cutter into the dry, rock-hard ground. It took a little adjustment to the turnbuckle on the RH 3-point lift link to get it to cut level.

View attachment 104253
Wow! That's working nicely!! Watering the lawn the day before in the area that will be "stripped" might help with both the stripping and giving the rolled up sod some nourishment if it won't be laid down and watered in shortly. But if you're not going to relay the sod.....then who cares.

That cutter will be a handy tool in your attachment portfollio!! Very NICE!!
 

leveraddict

Well-known member

Equipment
2017 BX23S 60" LP BoxBlade 54" mower 60" BackBlade EA 12" 1 bottom plow & Forks
Apr 1, 2019
906
580
93
NEPA
Nice work and fabrication! Putting the old sod back will save you a lot of extra work!