Search results

I have a woods rd7200 mower that i use on the 3pt hitch of my L2501. It has started to have a little bit of belt vibration when pto is engaged. Spindle bearings are tight, idlers seems tight not much wobble. I have a video but im not sure it will allow me to upload it, only allowed me to...

Does anyone know if these threaded bolts with nuts on them are suppose to be tightened or loose. There are several of them for the pins on loaders. All seem to be loose, was just curious how they should be. Loose or tight

Thank you for that info, exactly what i was looking for. Are you still fabricating stabilizers. How far out is the wait if so. Thanks

No i have not pyrchased the stabilizer kit yet. The stabilizer is without a doubt wider than the turnbuckle.

Hello everyone. I have questions about the kubota stabilizers and what implements people have found to not work well with. As in the stabilizers rub against R4 tires, and with turnbuckles it will not rub. I mainly use the tractor for mowing. Woods RD7200 finish mower is what i use.

Kubota l2501 200 hr oil change filter leaks from the bottom. Hand tightented it and gave it a little more turn to snug it up. Have bought another filter to see if it was a bad filter. Nothing wrong with filters. Looks like there is nothing wrong with the housing as ive cleaned it and inspected...

Hello all, I just did a 200 hr oil change 11/11/2022. Heres what i have to say. Filled with 6 quarts of kubota 10w-30 oil the dip stick reads just above the top hole on dipstick as pictured on this forum. now what makes you wonder is before i did this oil change my dip stick read about an inch...

Anyone ever buy kubota orange touch up paint for small little spots? How good of a color match was it and what did you buy?

has green in it. Just need to top off only has 133 hrs. Will change it eventually

Looking for someone to just tell me the exact name brand to use.

L2501. Coolant reservoir is just below low level. What is recommended to top off. Not looking for the scientific make up of what coolant is, just what people put in their kubota tractor

With my L2501dt there is no need for paying the extra for cruise control. The l2501 is perfect tractor for mowing. Set the rpms with the hand throttle pick a gear and put your feet up and relax

I have a 6 ft woods rear discharge on my l2501. Bought it on craigslist for 750. Cheapest one i could find all other ones were 1200+ Very well built

I have an L2501dt. First tractor i have ever bought. I run heavy equipment for a job and this little tractor gets the job done just fine. Pretty sure the 25 33 and 39 all lift the same weight. I bought the 2501 because i plan on keeping it forever and can work on it myself without having to deal...

The dealer probably didnt load the tires because the weight of the backhoe will work. Maybe you didnt get the 3 point arms for it so they fogured you would never be taking it off? Not sure. I have a l2501dt and i used the kubota 10w30 that they sell at the dealership for my first service

Looking for some info on post hole augers. I am setting telephone poles in the ground. The widest pole is 13 inches and the rest are around 10 11 inches. I am wondering if a 12 inch auger bit will drill a bigger hole than 12 inches.

I have a woods7200 (6ft) finish mower for my l2501. Works great. Like many people have said its a finish mower so not much can vary between the brands. I also have a land pride brush hog that i can use as a finish mower in my fields

When i go to dump my bucket with a load in bucket it seems to dump as it should till about half way and then slows way down. Is this only because i am going up at the same time as i am dumping. Its a dt so yes i usually have the clutch engaged with foot revving the engine up

Put some fuel in it and start it up!

when i bought the tractor i bought a brush cutter with it so i will not be using it for that. I have used my neighbors 7ft finish mower and it worked great. A bit big but worked. For me my property is all flat. Very little inclines.