Search results

I just got this FEL connected on this tractor and the Controls don't work. The RAMs for the Tilt were removed. There was no oil in them when they were reinstalled. The Lift Rams were not removed. But the FEL has not been used for 5 years. When I used the controls, I had a slight movement for...

Thanks, I found someone that could measure the pitch. It was 1.50 I ran a tap through the nuts and a die on the Wedge. They are good now. Thanks, I found someone that could measure the pitch. It was 1.50 I ran a tap through the nuts and a die on the Wedge. They are good now.

Thanks, I found someone that could measure the pitch. It was 1.50 I ran a tap through the nuts and a die on the Wedge. They are good now.

Thanks, I found out that they are 1.50

I have a B8200 Tractor with a BF 300 FEL. There is a Wedge bolt that holds this on the Tractor. The threads on this bolt are messed up so I need to chase the treads. I know that it's a 16mm bolt. But don't know the pitch. Can anyone tell me what it is?

Hello, I have a B8200 with a BF 300 A Loader. I want to know if anyone can tell me how the Ram that tilts the bucket comes apart. I don’t see a snap ring. I was wondering if you can use air to push the seal out of the tube with the RAM or if you have to have it cut the tube open and then...

Thank you very much for this. It explains the position of the 4 support Arms.

Hello, I have a B8200-HST-D with a BF-300-A loader. I want to know if anyone has a Manual for the Loader, or knows where I can get one. I want to remove it from this tractor and put it on another B8200. I found that there are 4 arms that are on the loader and I think these are to hold it up once...

Thanks for the words of wisdom.

Thanks for the your input. I'll know more about the other tractor tomorrow. Depending what's wrong with the 4x4 will steer me into which tractor I fix.

Thanks for the Help

I currently have a B8200 HST-D with a loader and OLD Turf tires, a bad seat, questionable Wiring and Radiator, and no 3 point hitch arms. I bought it Not running and have be struggling with getting it to run. But that's for another post. I now have a opportunity to buy another RUNNING B8200...

Thanks everyone for your response. I did finally find the Spec at 0.0071 to 0.0087 Cold. Thanks 85Hokie and Northern Idaho Wolfman for the 0.008 Spec. That was right on.. Not thrilled with GeoHorn's response. Thanks both armylifer and D2Cat for that added comments.

I have a D950 in a B8200 and Need to know what the Valve clearance is. I have a couple of service books and can't find the correct value adjustment. Thought I had found it once before and it was about .020 but I'm not sure.

I have a B8200 with a D950 Diesel and just did a valve job. Now I can't get any fuel to the injection pump. This is my first diesel so I need a little advance. I fund that this D950 has a Lift pump and I can't get any fuel pass it. I also heard that they can leak fuel into the crankcase. Is...

I found a belly mower that is model RC54-71B. I think that it was under a B7100 HST tractor. I want to know if it can be used on a B8200 HST-D tractor. If it can be used do I need to do anything special? What is if worth? I would also like to know what is the correct rims and Tires for the front...

Did you find a Manifold yet. I think I know where there is one. I'll check on the price. Where are you located? I'm in Wisconsin.

I also have a B8200 with a D950 Engine. I had to pull my head and I was lucky that the head was not cracked. But I did have to buy a upper Gasket set and Values and Springs. I don't know if you got everything for your tractor yet. But I did find a good supplier with actual Kobota Parts And The...

Thanks for the Information. The book I have said to start at 10, 14 to 1. I'm assuming That your sequence would be 1,6,4,2,5,3 9, 7 and so on.. Thanks

B8200 Operator Labels I own a B8200 HST tractor and want to know if anyone has a source for any of the Operator labels that are on this tractor. If know one makes them, then I would like to know if anyone has a B8200 that still has legible labels that they could photograph and send to me. I'm...