Search results

I have this 900x side by side that had been submerged completely in water. over the past year i have been plugging away at it fixing this and that. i have it running and drove it around a little bit and now there is water in the oil. I changed the oil and ran it for a few minutes and it gets...

A while back I posted about a RTV x900 that had been submerged under water for a time. I've come a long way with this machine. The machine is running after replacing the fluids, starter, alternator, injection pump,and injectors . After operating the machine the oil level in crankcase has...

Our skid steer developed a fuel leak which we traced to a steel line that runs to bottom of fuel rail. With great difficulty managed to remove that steel line. It was cracked from the end connected to rail. Installed a new line and after a minute it is leaking seemingly more. Verified the...

Hello all, I replaced the compressor, rcvr/drier, expansion valve and condenser on our 9540. I flushed the system thoroughly and used a 2 stage vacuum pump for several hours to evacuate. 4 ounces of oil and 30 ounces of refrigerant as specified. It is working great. I don't have a...

RTV X900 rebuilt fuel injectors do not thread in completely. Put in new cup shape heat shield and new copper washer. I start threading in the injector and the last 10 threads or so it stops tight. All 3 thread in about same distance, 10 threads from being all the way in. I'm not pushing past...

Our SVL 95 skid steer AC blower motor is working at all speeds, however, not getting a lot of air flow. Checked for blockages in tubes etc. Cleaned the filters. I pulled the resistor our of case and watched the blower motor turning but not feeling much air. Consequently, the cab is not...

Cleaning out our 4160 baler, my best tool is my B and D leaf hog. The blower is pretty effective but can't get at the clumps in the corners. Any suggestions on how to get the hay out? Some machine setting on?? Any help is appreciated. Gift

Cleaning out our 4160 baler, my best tool is my B and D leaf hog. The blower is pretty effective but can't get at the clumps in the corners. Any suggestions on how to get the hay out? Some machine setting on?? Any help is appreciated.

this rtv x900 was fully submerged in water for some time. it has been a project getting the water drained and fluids changed. it is fortunate none of the machine's fluids were milkshake. as you would figure the electrical is a concern. the alternator, starter and fan motor were all boat...

A brief history, last year this tractor was leaking hydraulic fluid from the transmission vent on left side of tractor. The fluid was foamy with micro bubbles. Fixed the suction side defects, replaced filters and replaced fluid. For the most part of the past year the machine operated with no...

Sometime ago, our m 9000 had hydraulic fluid pouring out of the transmission vent. The fluid was full of tiny bubbles, the tractor was sucking air. This issue occurred right at startup. Even though the fluid was overflowing, the hydraulics worked fine and the tractor rolled. With the help...

Our m9000, can, front loader, 2 wheel drive has hydraulic fluid coming out of trans vent. I have posted about this previously and followed the recommendation. Initially, when operating tractor hydraulic fluid poured out vent. The fluid was saturated with air bubbles. What has been done? The...

This is an ongoing problem with our m9000. I have received very helpful information. After running the tractor around fluid starts coming out of vent on top of transmission. The fluid is full of bubbles, which I learned on this forum indicates air is being sucked in to system. I have pulled...

M9000 front loader, manual transmission, started leaking hydraulic fluid from vent tube on top of transmission. I was moving hay bales, front and on 3 point when I noticed the severe leak. The fluid seems thinned out. I shut down and let machine cool off. I checked hydraulic level on level...

Our m9540d is running normal. Recently, I have noticed when I shut tractor off, I hear what sounds like a fan spinning down when you take power away. I have isolated it to the area of the turbo. This is a new sound and there is no apparent new noise when running tractor. Shut it off and you...

Now with literally freezing temperatures, putting the glass doors back on tractor has become a priority. I'm going to put the hinges, pull bar and latch with new rubber. I've been told horror stories about the glass shattering so I'm looking for advice or tips to get these doors assembled and...

Our m 9000 has developed an oil leak from the front crankshaft seal. It's pretty steady. Can anybody tell me if that seal can be replaced without removing front cover? I'm going to need a repair manual to do this job. Any recommendations? I'm unsure about these various online manuals...

I recently posted about a no start skid steer svl95-2s. Now we need to get it off jobsite and to dealer. Can this tracked vehicle be rolled when disabled...some way to disengage drive sprocket without disassembly?

2016 SVL 95-2s skid steer cranks but no start. Was running then quit. We changed fuel filter, drained old fuel and refilled with k own good diesel. We've purged the air procedure and all we are getting is crank, start for 4-5 seconds then it quits. This is an improvement, however, it just...

We have a newer m6060 that has the hydraulic block on rear for implement connection. We also have a m9000 with 2 of these blocks stacked on top of each other. The units look the same have same dimensions. Is there any reason why we can't take one of the blocks from the 9000 and stack it on...