Search results

I found the problem, the belt had come off.

I was mowing today on a L2501 with a FDR 1672 mower. Unfortunately I very slightly ran over some river rock and the Mower stopped spinning, the PTO Shaft was working not the blades. Also I broke a blade. Honestly it barely got into the rock (size of eggs). My question where do I look first...

I have a L2501 with R4's as for use of the tractor is 89% mowing 2 acres, snowplowing flat drive way/parking is roughly 90 ft by 100 ft. At times I wish I had turf rubber but then if I had turf I wish I had R4s. The only down side of R4s is they can and will dig into your turf when sharp...

Thanks you everyone for your advice. I went to you tube and Messicks had a video on there about this situation. They said that the older tractors you would have to deal with the injectors, but no longer. Just fill it up and wait for the fuel gets to where it needs to be. After many attempts...

I know better, but today I ran out of fuel in my L2501 while mowing. I have topped off the tank but after many attempts it only turns over with obviously no fuel getting to where it should be. Is there a trick I should know? Or do I just keep turning it over until the fuel gets through. I am...

https://www.facebook.com/marketplace/item/287344486367332/?ref=search&referral_code=marketplace_search&referral_story_type=post&tracking=browse_serp%3Af2a0ae45-4e1d-41f9-a6d7-120f0

No problem, they are listed in Market Place on Face Book.

Thanks I was 99% sure they would not work.

I have found a set of turf tires and wheels that came off a B7100, the tire size provided per ad are fronts: 20.5x8.0-10, rears:29x12.50-15 These are different sizes then on the tires on my L2501. My question is will the the wheel off a B7100 fit my L2501? Pretty sure they won't but would...

Re: FEL Hydraulic ?? Thanks everyone, I used the tree method and now I am back to getting my work done.

Re: FEL Hydraulic ?? I guess the best way to describe is if the bucket was not on the FEL and you went to curl the bucket both sides do not work the same.

I hope I do not have a major problem. Yesterday I was moving rocks for landscaping with my L2501 with a LA525 FEL. Today when I started using it the bucket came unhooked on just the left hook up where it hooks to the bucket. Now the two cylinders do not synchronize with each other. In other...

"Keep your blade tilted back", Do you mean keep the top of the blade tilted forward, which brings the bottom of the blade tilted back?

Thanks i will be careful the next time I unhook the board next timr. I have learned since that I could tap the needle in the coupling with a hammer and wood fowl to release the preasure.

Every time I hook up my fel hydraulic hose's I always have problems getting them reattached (quick couplings) today as in the past I have waited for the pressure to go down as well as move the fel controls to release pressure but no luck. Is there something I am missing or a secret to this...

Thanks for the replies, Yes Hokie it is Hst and As Far As The Slope Of Access It Is Concrete And Looks To Be Not A Steep Grade. Sorry About All The Capital letters not sure why they come up that way.

I own a 2501 and need to know if it can handle pulling a 20 or 24 foot pontoon boat on trailer. I love a quarter mile to a lake public access and would purchase a pontoon boat if the teacher can handle this??

Thanks for your help, I went to a local automotive store and purchased a pickle fork, three pounds with hammer and it was off. I knew there was a special tool to do this, probably would of broken something if I kept on. Thanks again, this forum is great.

Yes a picture would help I will post after work today. Thanks

I did d knuckle head a broke the right steering linkage on my 2501, this is the adjustable one. Have purchased a new one, know the challenge of removal on. The part that broke was nearest the center pin. I talked with mechanic and he said the end of where the threads are is tapered and is...