Search results

I spray all my exposed cylinder rods with Fluid Film. Been working great for the past 5 years.

Mine wouldn't start one day and it turned out that one of the PTO levers (I don't remember if it was rear or center) was not in the neutral position. I started to panic when the engine wouldn't crank. I started checking everything and found the PTO lever issue. It wasn't out of neutral by...

I haven't operated an L3800, but...the 3800 is an L series tractor while the 3200 is a B series. The L series tractors are much heavier than the B's so the extra HP may be needed to make it work the same as the 3200.

Not if they're Daisy Duke overalls!

My wife had the same problem. I thought my idea was the best, I suggested she buy some new boots for when she drives the tractor. These immediately came to mind***8230;. After spending a week sleeping in the barn when the boot idea was rejected, I removed the plate from the bottom of...

It took me all of a minute or so to drop the bucket off my FEL when I welded my hooks on. It may not have been necessary but it was worth the piece of mind to me that I wouldn't have any problems. If you don't want to drop the bucket then I would suggest at least disconnecting the battery...

Love mine. It's great for pushing brush around and it bites into dirt much easier. This winter has been a bear and I found it works really well getting thick ice of the driveway.

Word of warning about the Piranha bar.....IT'S VERY SHARP!!!! I always make sure that it's down flat on the floor when I park the tractor in the garage. The last thing you want to do is nail your foot, ankle or shin on the teeth of the bar. They are really sharp from the factory.

I've got a 60" bucket on my B3200, so it's the same as your's on the B3030. It works great ripping out small trees and brush. I burned a big brush pile last month and the toothbar came in handy pushing the brush up on top of the fire. Here's a photo of what the Piranha looks like on the 60"...

Any photos of this around anywhere?

I've got a set of Mark's stabilizers on my B3200. Makes hooking anything up on the TPH much easier. It takes all of about 5 minutes to install them and once they are on, seconds to adjust when you put an implement on the the TPH.

I know this is an older thread, but I've got a B3200 that I would like to adjust the timing on too. Any updates on how it worked out and did you need to advance or retard the timing? Thanks!

I've got a bh77 on my B3200 and I can do multiple movements at the same time....I don't know what I'm doing so I still do one at a time... But, the backhoe is capable of doing it as I tried curling the bucket and gathering in the dipper arm at the same time with no problem.

I added a section of 3X3 angle across the top of my bucket and welded the hooks to that. I also added clevis mount points on top and one inside the top of the bucket. I also welded a hook on the lower section of the back of the bucket to bring it closer to the tractor in case I needed to lift...

Thanks all. The "pasture" section only gets mowed about once a month. By that time it's too much for the JD lawn tractor. I'm not really looking for a finish mower, just something to knock down and chop up everything. I'm one of those people that hates to borrow tools or things like that...

I've got the itch to buy a rotary cutter for my Kubota B3200 (with FEL). We don't have acres of pastureland or orchards, just a couple acres that includes a field that we only mow once every month or so. Before I go out and spend my money I thought I'd check with you guys to see if I'm about...

I've been thinking about getting a 3 point hitch snowblower but with my luck I'll buy one and we'll never get more than an inch of snow ever again! Before I forget, Burtonbr, thank you! That's the exact info I was looking for.

You betcha! Good thing I have the tractor though. When we had that major blizzard in early February we got 30+ inches of snow overnight. I only managed to get the Rhino about 6 feet out of the garage with the plow. I used the tractor the clear my driveway, my nieghbor's driveway and an...

I've got a B3200/LA504 loader with the Kubota OEM Quick Coupler. I want to to get a pallet fork attachment but I don't want to use the skid steer quick attach. (It's $700+ for the adapter) Does anyone know the model number for the Kubota OEM pallet fork attachment? I searched all over online...

I have to fight with my wife to get seat time. That's what happens when you marry a farm girl!