Search results

don't see a sight glass anywhere...... how full do you put hydraulic fluid in the tranny? and this is a tractor that shares hydraulic fluid between tranny and hydraulic system right? PS- I searched first

THE GAP (in the door) Maybe one of the awesome Orange Folk in here will have an idea. Per Scottmandu suggestion at SteelSoldiers, door handles on LMTV's like mine tend to break more often if one has misaligned doors etc. causing extra force to open/close doors. Sooooo after replacing my broke...

3 feet from an outer wall I am setting up an old RV I just bought for a friend to live in while he heals. Probably will be about two years. Hot water heater (50 Gal) is inside of that wall in the house. House is one bed one bath... only myself in the house... maybe plus one in near future thus...

still connected to house box and pole... it just got knocked down by a branch. It still works, am on it's internet now. It has an exterior jacketed wire (part of same jacket for whole wire) disconnected at a break in the line.. might have been that way before coming down. Ground? Is that...

Anyone see an issue with using a suspension seat for a tractor orr? in a truck? I've got to have low profile and a little is better than nothing.

Did a search and there is ton of threads.. all with good tips in each. Hope to get this to grow with all the tips etc. in one place. . How long should the shaft be to mate "your" tractor and implement? One can cut them to fit. They need to be Short Enough so inside and outside of telescoping...

Once you recognize a spam attack is on and see that Moderators and starting to delete spam... please stop reporting each new spam that pops up. Sounds crazy but yes. Once moderators see attack has started we pop in as often as we can in our day to check the board and delete as fast as we can...

This thread is only for maintenance/repair mentions "specific to an implement"... AKA something fun to note but basically does not need a whole thread to explain. Can add link to another thread with more detail if needed, so not to get carried away in this one and hijack the thread. NOTICE...

So thinking little out of the box. Considering movable side mirrors on my truck I can move from inside truck. Large movements. Basically sideways Submarine periscope. Extend a foot and a half and/or retract it right next to cab. Not a little truck; poor mans Expedition camper based on...

Purchased an 18 foot flat bed Tandem axle trailer with pintle hitch. No deck installed. Wheels BELOW deck height. Will be pulling it when needed with an LMTV1078 (soon to have Ambulance box on it creating an expo camper of sorts) So I've not had a garage since Gulp.. 2004. Had that about 2...

Friend passed onto me an IP with a 12v Fuel solenoid shut off from an engine he had. (similar yanclone). I want to install this on my Yanclone. His appears to have had only one Timing Shim. Copper. Pump that came off my engine had same shim plus two paper shims. Should I go with the...

Newlyme has volunteered his time to create "groups" where people can go, to get aid or just meet their more local friends. You can post direct to the group for messages about........ anything local to you such as.. get togethers, wrenching weekends, Need of a rescue etc. Sooo go to your "User...

Newlyme has volunteered his time to create "groups" where people can go, to get aid or just meet their more local friends. You can post direct to the group for messages about........ anything local to you such as.. get together's, wrenching weekends, Need of a rescue etc. Sooo go to "Social...

This info was kindly PMed to me Will put link to this thread in sticky as suggested. Oh and there are links in the Fabrication Sticky about homebuilt solutions.

Not sure that it is a good thing or a bad thing that there was no Kubota's in this (that I saw) 5XrU3Ejx0_M https://www.youtube.com/watch?v=5XrU3Ejx0_M

Picking this up Fri. 2.5 hour drive away but for only two digit price... worth the drive. Helps I get 40ish MPG too. Looks like it needs 1/2 of PTO shaft and repositioning of plate that one tractor pin is on. Anyone see anything else or have recommendation on bending the pin plate? Looks...

in Atascadero https://slo.craigslist.org/grd/6125813239.html Not mine..... no affiliation

ok... now I feel stupid. I know how to look up a tractor then get parts schematics..... How do you do this for implements?

Thinking on adding one of these to operate off my PTO. The thought is to get a PTO saw and add this gizmo to the opposite end of the shaft that spins the sawlade https://detectorcovers.com/wood-log-splitter-screw-80mm (example ... not yet vetted what product to purchase) Anyone got ideas on...

There is a 28" bladed buzz saw for sell near me. There is another that looks little smaller. Both PTO driven. Just don't know if my L235 has enough juice. I would assume so... but you know what they say about Assuming :D So what's ya'lls experience? What about crazy idea of adding to the...