Search results

Got this from my dealer: Floor mat 3C001-55062 Floor mat fasteners 7 req’d Z67955-51340 Says it fits on the M5660. I plan on removing the floor pan and taking it down the road to the Rhino Lining place and have them spray it.

I just bought 3 of those but the lettering and graphics were fuzzy...like a photo that had been blown up too much. I was disappointed.

I like the Precision Mfg 333D72 clamshell grapple. Dual lid, weighs about 600 lbs, opens 50".

Haven't done it personally but don't see any compelling reason why you couldn't or shouldn't.

My experience with State Farm was that I could take out an "all perils" policy on the tractor that would cover everything except operator error. When the agent ran the numbers SF came back and said the tractor would be considered "heavy equipment" and the premiums were HIGHER than KTAC. So in...

I prefer Berne Apparel insulated bibs and here's why: They have heavy zippers from the ankle to the waist, plus one from the waist to the chest on the front. The insulation goes all the way up the back to just below the shoulder and all the way up the chest. They are reasonably priced. They...

A friend of mine has a Woods back blade with the hydraulic angle adjustment. It has a cartridge style relief valve (Sun Hydraulics, et al) in a manifold mounted on the frame of the blade. If you strike a solid object with the end of the blade it allows fluid to pass from one port of the...

As shown on your owners manual, "multipurpose grease" NLGI 1 or 2 means the window is wide open. I use the 3% moly grease, pick your brand, for everything with no issues.

Anybody have one of these on their loader? Thinking about getting one on my tractor when I order it. Pros-Cons...is it worth the $$$ or not so much? Thanks in advance.

An overrunning clutch only prevents the implement from back driving the tractor when you disengage it. They don't feather the power at startup.

I'd trailer it too.

Thanks for the replies...seems like with the right LCD panel Kubota could have easily done something that would have been a little easier to understand. Maybe the PTO icon with the rotational arrow and the abbreviation rpm. Oh well, until I get a job in the engineering department at Kubota...

I was browsing through the M5660 manual that I printed off the internet and in the section on the PTO/engine hour readout operation there was an illustration that showed what the display would look like in the PTO mode and it was 540 n/m. What does n/m stand for? I can figure out r/m to be a...

I run my cutter with a few inches of lateral movement but I'm not nit picky about the cut quality...it's not a lawn so I don't really give a rip. You want a little slop in the setup for when you nudge a tree or fencepost, etc..

I put some long shoulder bolts on my pallet puller, found a spring that was the ideal size, then cut a piece of 3/4" PVC pipe that fit nicely over the spring. I put the shoulder bolts through the hooks on the spring so that it will hold the jaws closed around the tree.

I have a pallet puller that I use on trees from 1"-3" diameter and it works pretty good. Sometimes will rip the bark off but typically bites down after that. It's a good tool when you have a helper on the ground to hook it back up if it slips off. If I'm working alone, a chain with a choker...

Interesting stuff. I wasn't aware that the M5660 has both the position and draft control for the 3 PH. The specifications on Kubota's website shows position only. Is this an older tractor or is there simply a typo on the Kubota specifications?

Those blades can easily be shredded and the resulting fodder separated for salvageable metal, etc.. http://www.ssiworld.com/en/watch_it_shred

A buddy of mine had a Curtis cab on his JD 1025r. Used it for a year and sold it for pennies on the dollar just to get rid of it. He had to add fuel from inside the cab because the cab was outboard of the fuel filler...nice if you spill a few teaspoons full. He felt that the cab made the...

Great video! Music was fine, but I like "tractor music" better!