Search results

Ok, that sounds good. The posts are only used for a deer fence around my garden. So it'll be holding up a light net. So it sounds like this job would be easily done with a backhoe.

But wont the post move? It sounds like it would be loose

I need to install about 10 cedar posts of 8" diameter. The soil here is rather rocky, so I think I would be wasting my money if I rented a gas powered post hole digger.I'm thinking I can just use my BH to dig 3' deep holes and then put a 10" sonotube in the ground. How tricky is it going to be...

Turns out the hardware store 2km from me now has a hydraulics section. I found the right adapter and everything is back on track. Thanks everyone.

100$ delivery fees to canada .... I'll look around in local stores. At least I know what I need now. Thanks!

Correct, what I have now is 3/8 NPT female by SAE-8 male. The inlet ports 1/2 bspp as per the information you gave me when looking for a PB sleeve in another thread. Not sure why you need the size of the cylinder ports but here it goes: 1/2 bspp also. The plug on one of the cyl port fits on...

Thank, I'll make some calls tomorrow. Bspp seems hard to find. I doubt I damaged the threads, it goes it very smoothly.

The picture is old. It's from when I initially bought it. Everything is the same now, but with oil and diry all over it. I took a picture of the plug that can with the valve and it looks like the rubber is inside the head. Never seem that before. So yeah, not ORB it seems. And this is what I...

It is slow in one direction because I have a leak that happens when I activate the valve in that direction. Before I had the leak, it was not slow. I came to realize this while trying to troubleshoot this problem later on. I'm wondering if it's because the hose connected to the cylinder for...

It's this guy. The leak happend beteen the orb fitting and the valve block (so not where the teflon is) Are you guys suggesting I should try replacing the fitting and also the o-ring? One strange thing: it happens only when pushing the valve one way, but not the other. I get no leaks when...

Yes. The o-ring pops out on one side, the oil is pushing it out on one side. Kinda like a rubber bubble forming. I was using the same o-ring that was working for 2 years and it did that. Then I bought new ones from a store that sells hydraulic hoses so I figure they have the right o-rings too...

I have a Vevor valve that I bought for cheap from china. I use it as my rear valve for my snowblower and wood splitter. I understand that this valve is cheap but I never had a problem until today. On the pressure side, the connection is ORB. Today, while splitting wood, the oring popped out on...

My father in law wanted a rear weight since he doesn't have a backhoe. I had a few concrete blocks from a wall I cut off 2 years ago. I estimate it weighs around 500lbs. Only goof I made is that the 3ph attachement is too low. So I have to sit the block on something 1ft off the ground to be able...

I kept having issues with the right side pin that keeps the FEL legs up on my tractor. The pin would bend or loosen up and fall. Yesterday it happened again and the leg came off as I was pulling a tree with the bucket so the leg bent while it was dragging on the ground. The hell with this, I...

So this could be avoided with regular inspections then. Kinda weird it got loose. Maybe some threadlocker too?

I'm surprised this thing broke. We all have the habit of pulling harder on the lever to get more power out of the machine, even if we all know it makes no sense. But to the point of shearing the bolt? I didn't know this was possible. It happened while digging out a stump. I was almost there. I...

That video seems to show a factory made bucket. I'm looking for a picture of a converted bucket using a weld-on plate

I'd like to see what it looks like, specifically on a B2601 or any other 54" bucket. The weld-on plate looks bigger than the bucket and it seems like it would stand out higher than the top of the bucket. Also, I'm not sure how high it should be welded. A few pictures could help me figure out...

Will a ssqa bucket / fork / blade or other fit on any tractor equiped with a ssqa? For example, the same forks could be used on a b2601, L25, LX26 .... I guess that's the whole point of having SSQA. Obviously sharing buckets on a b2601 and L01 wouldn't make much sense, but will it work?

That is exactly the kind of post I was hoping to see BEFORE I has to let go of the idea to upgrade because of the price difference. 😂. It's nice to see them side by side. The difference is real.