Recent content by CCox

  1. CCox

    Kubota Hazard Flasher Unit vs CF14

    I rebuilt my hazard lamps with new sockets, bolts, 1156 LED lamps, cleaned and refurbed the gaskets and polished the lenses. Did the same with my headlamps, separated the glass from the housing, painted the housing interiors with a reflective silver coating, cleaned the glass interior and...
  2. CCox

    B8200 Engine, Sheet Metal Misc

    I shipped a deck through Uship.com and it was much cheaper than Fastenal. Fastenal also suspended their shipping operations when covid started so they were not an option when i needed it shipped.
  3. CCox

    Kubota canopy by Full Vision in west PA

    I am in Armstrong, Jefferson and Indiana counties often and would like to get a better look, take measurements, etc. I have a full vision made ROPS but don't know how these were mounted. Can you read their model number?
  4. CCox

    Model 2020 Grader/Snow Plow for sale

    Also interested. Thanks.
  5. CCox

    Kubota Hazard Flasher Unit vs CF14

    Female terminal ends were covered with heat shrink to prevent arcing or inadvertent contact with grounds or hots. The dash pic came from a video I was not able to upload. The hazard button flashes with the amber lights.
  6. CCox

    Kubota Hazard Flasher Unit vs CF14

    I received my flasher relay and hazard switch. These I obtained from Amazon. The flasher is a CF14 LED flasher with 3 terminals. https://www.amazon.com/gp/product/B00XAU66V4/ref=ppx_yo_dt_b_asin_title_o01_s01?ie=UTF8&psc=1 The hazard is a 19mm push button type with illumination. I wanted...
  7. CCox

    Kubota Hazard Flasher Unit vs CF14

    My old hazards were rusted and sockets heavily corroded so I took them off and welded the holes closed. Same with the tail lights, but they were gone before I got the tractor. My plan is to mount amber and red LED lamps to the ROPS so they are higher and amber can be seen front and back. I'm...
  8. CCox

    Kubota Hazard Flasher Unit vs CF14

    Does anyone have experience in replacing a 3 prong Kubota flasher unit (in my case #35170-33700 @ $60+) for a 3 prong CF14 Electronic Flasher (suitable for LED hazard lights)? My B8200 schematic shows the White/Red coming from the fuse, Black to Ground (Earth), and Red/Yellow going to the...
  9. CCox

    Flasher unit

    I know this is years old but I was researching flashers and found your question. With regard to flasher relays, I believe the letters correspond as: B, X, + 49 = Battery (Power Input) C2 = Hazard Switch Ground E - 31 = Ground H = Hazard Switch I = Ignition L, 49a = Load P = Pilot Lamp S =...
  10. CCox

    Restoring a B8200

    I am in the process of doing the same. I have the formula for both gray and orange paint, with matches made from original paint that was covered from exposure. I will photograph these for you. I bough All Surface Enamel (Oil) from Sherwin Williams and shot it with a HVLP gun. Decals have...
  11. CCox

    B8200DT Questions for the knowledgeable!

    I am repainting at B8200 and have run into a few questions and need the advice of the experienced. First, as I was cleaning the PTO area of flaking paint, I came across threaded holes above the PTO in the cover that were partially filled with something that looks like glue from a hot glue gun...
  12. CCox

    Chris, Would you have a transmission and a carburetor for a W5021? If so, how much for each...

    Chris, Would you have a transmission and a carburetor for a W5021? If so, how much for each? Thanks. Chuck Cox 412-551-2835
  13. CCox

    I saw that you bought a snow blade for your B6100. I found a blade that the seller claims fits...

    I saw that you bought a snow blade for your B6100. I found a blade that the seller claims fits a B6100 and B7100 but he has not had it on a tractor. I don't think he ever had one and it was on the property when he bought it. He can find no numbers on it. I am trying to find out if I can...
  14. CCox

    Wanted to buy three point attachment for B7100 d-p

    Kaze, I saw you inquired on the one being parted out. I'm just down the road from you and I use a great guy for fabrication in McCandless. If you find your parts but have something missing, I can put you in touch with him and you can use mine as templates if they're the same. I have a B8200.