New profile posts

Has anyone installed bung plugs in the fuel tanks on a L6060 to drain or decontaminate the tanks without having to pull them every time? We removed the tanks about 14 months ago and cleaned them, replaced pickup assembly, etc.. Now experiencing stalling issues again, found contaminants in water separator. Pulling the tanks is a very labor intensive chore.
The plan is two fold, pull the tanks again, install bung plugs in the bottom of each, and install a screen type filter on the pickup tube to prohibit diesel scum and other trash from being picked up and clogging fuel lines...
Any thoughts or insight you may have are welcome.

Looking for a ROPS for L245DT. Can you help out?

New owner of Lx2620SU

Its coming along, I went to my machine shop in town and they said they'd make me a 15231-28470 and good thing because I've searched everywhere without an success. Tranny filled to the brim with diesel and it sat for a week after it was drained, vacuumed the sump to capture any debris and got it painted. its not extremely accurate coloring but looks decent. Crankshaft was completely destroyed, it was ran for some time without #1 rod bearing and the rod journals were 4 tenths of an inch different in diameter... Sleeves are .0001 out of round so were going for another 50 years on em. Everything I need to overhaul this little guy is in the mail, between eBay and Messiks I got everything I needed and then some. I'll keep anyone following along in the know.

BH75 backhoe
I am having trouble finding seal kit for 'ol orenge outrigger cylinders, 30 R x 65 B....

I have an old B7100 HST E and the steering locked up yesterday. I saw your posts in the thread on "Fast B7100" from April/May of this year and wanted to reach out to see if you might have that part. I believe the HST box is different from the non-HST. Thanks!

L3800; Hydraulic oil check; is there an alternative way to measure the oil level other than the ridiculous window and it's placing ?
The window always been difficult to see but now it's opaque as if blinded. I"m considering draining the sump and refilling with the correct level of 6.2 gallons , it won't solve the problem for future level checking. Any suggestions would be gratefully appreciated!

I have a older Kubota with low hours( 360) was just sitting there warming up and then just died. Now when you turn key to first position it makes some weird noise like relays chattering and when you go to glow plug warm up position the light comes on but when you go to start position, nothing. Any ideas?

Thank you, Hugo.

Hello I am looking for a used engine for a M8540. Where is the best place to fine one?

Currently noticing that I have been a member since 10/2021 and I am also a New Member.

Wishing the hydraulic tubes on my loader were numbered by order and position in which they should be installed and their final position inside the channel of the loader arm….

Looking for wiring harness for L345, do you have one?

I bought a hydraulic pump for my B8200hst tractor and found when it was delivered I bought the wrong one. Do you happen to still have a left rotation pump?

I am trying to get a shipping quote from Valley Cartage, but they need name and delivery address. If you are still interested please send your contact information. Thanks.

BTW: As I mentioned in the original post this valve will run the "UP-DOWN" function on the BX2200 snowblower but it does not have enough hydraulic connections to run a front end loader (FEL).

I have a Kubota T2290KW 42" with a mulching kit and I am attempting to reinstall the mower belt which came off while going over a bunch of branches. The manual is not very helpful. My question is when reinstalling the mower belt ,does the belt get installed between the pulley and the guide pin or does the belt get reinstalled on the outside of the guide pin. Please help!!!!!@

Trouble withB7200 4WD
Over past several months 3 point hitch getting weaker and not going as high. 3 point will also not stay up and leaks down, Fluid good and screen clean……tractor 35 years old….pump going out and bypassing internally ? Suggestions
Tomt

great remedy to buying a new tractor. Have you come up with a price and or a video to do the install including you're parts?

Just acquired a G1800.