which mfr for grapple?

[Orange1forme]

Looking for attachments for my B2650 with cab.

At this point I am looking at a grapple, rear blade(other post on this already) and maybe a spreader(for sand in the winter mostly) and pine needle rake.

Everything attachments seems to be heavily represented on youtube and possibly the same mfr for a couple other brands.

Looked at Land Pride, of course, as well.

Any comments, recommendations or caution for any mfr or particular product?

Thanks

 

[Sodark]

I've been passively researching this for my 2650 as well since June. Always curious to hear responses.

 

[nbking]

Everything attachments is who I will be using for my grapple. They practically beat the crap out of theirs showing how tough it is, and their 55" wicked grapple is the lightest (200lbs), it will work great on my L2501. I have not heard any bad stuff about other grapples, but for the smaller tractors weight can be one of the more important issues.

 

[Hook]

I purchased the EA 60 inch wicked root grapple for my L3240. It is built tough and weighs approximately 150 lbs more than my bucket. It has done everything I have asked of it. It is my favorite implement. I also purchased the WR Long third function valve.

 

[Cpcareyct]

I purchased a Wicked Root Grapple (for compact tractors) from EA
It's a great purchase for my L3560.

 

[Mainah]

Everything attachments is who I will be using for my grapple. They practically beat the crap out of theirs showing how tough it is, and their 55" wicked grapple is the lightest (200lbs), it will work great on my L2501. I have not heard any bad stuff about other grapples, but for the smaller tractors weight can be one of the more important issues.

I agree totally. EA all the way. There’s a good reason they have a several week backlog.

 

[Kennyd4110]

Take a look at the Artillian modular system if you don’t already have forks. In addition to the forks you can add a grapple, rakes, small stump bucket, etc.

www.artillian.com

 

[Jchonline]

Probably the most important criteria is weight. Make sure you get a grapple that is well balanced with strength and weight. EA does a good job of paying close attention to this on CUTs. There are other brands, but I would always do a direct comparison with EA. Personally for a B2650 I would look primarily at EA. Maybe Artillian if they have similar pricing/strength/weight.

 

[GBJeffOH]

My Everything attachments grapple has seen hard use. No issues.

 

[fruitcakesa]

Take a look at the Artillian modular system if you don’t already have forks. In addition to the forks you can add a grapple, rakes, small stump bucket, etc.

www.artillian.com

Looks like they only have stuff for green tractors

 

[fruitcakesa]

Looks like they only have stuff for green tractors

My bad, I found the orange stuff

 

[Mister]

You guys wanting to buy a grapple... Have you tried pallet forks, set to the widest setting? I heard guys say you'd be surprised what you can do with them, and they were right. Of course not only can you lift logs and stumps and giant boulders, but you can pull up to a giant pile of cut tree limbs, brush or whatever and just pick it up from the bottom. It holds on to the pallet forks like magic, and you can drive with it like that over to where you need to take them. You wouldn't think it until you try it.

Sent from my SM-N960U using Tapatalk

 

[Winyah510]

Everyone has their own needs and opinions but so far, I’ve been lifting logs and brush with my pallet forks. Holding a 10 ft log with pallet forks on bumpy terrain is slow at best and not exactly efficient in IMHO. I just ordered the EA Wicked 55 grapple to make this type of work easier.

 

[NewtoOrange]

After a LOT of research I went with the Landpride for my L2501. Nothing against EA (will be getting a bucket from them) but the price, shipping and wait time made the LP thru my dealer the way to go. LP is about the same weight as EA, steel is actually a bit thicker, 2 pistons instead of one to close lid and also USA made. Love it so far.

 

[bearskinner]

You guys wanting to buy a grapple... Have you tried pallet forks, set to the widest setting? I heard guys say you'd be surprised what you can do with them, and they were right. Of course not only can you lift logs and stumps and giant boulders, but you can pull up to a giant pile of cut tree limbs, brush or whatever and just pick it up from the bottom. It holds on to the pallet forks like magic, and you can drive with it like that over to where you need to take them. You wouldn't think it until you try it.

Yes, I tried pallet forks first, and had a miserable two years using them. I move a LOT of brush and logs, and the forks were just inefficient. I picked up the Land Pride Grapple and have since SOLD the pallet forks. Not only do I clear 40 or so downed trees each year, I get semi loads of firewood, and use the Grapple to take them from the log pile to the wood shed for processing.
I also stack and move just about everything with the Grapple. It also works as a way to rake and pickup brush and ground fuel from twigs and branches. It is by far the handiest tool attachment to my Kubota BX25D

 

[Orange1forme]

After a LOT of research I went with the Landpride for my L2501. Nothing against EA (will be getting a bucket from them) but the price, shipping and wait time made the LP thru my dealer the way to go. LP is about the same weight as EA, steel is actually a bit thicker, 2 pistons instead of one to close lid and also USA made. Love it so far.

EA grapple has 2 pistons, at least the 55". Don't really see any operational difference between the LP and EA.

 

[jkcolo22]

EA all the way. Love mine and their customer service is second to none. You call their 800 number or email them and they are very happy to help you (before or after you make a purchase).


Sent from my iPhone using Tapatalk

 

[D2Cat]

I ordered a grapple from MTL in Tallapoosa, Ga. for my L4240. I have a friend who bought on and it seemed like it would do what I needed and didn't have to weight to receive it. I haven't used it a lot, but got a nice deal on it!

 

[85 Sovereign]

I did a lot of looking around and ended up getting a Tomahawk grapple. I'm using it on a L4701, and its a 72" with two grapple "claws." They don't sell through distributors, but you can get them directly from the manufacturer and sometimes through equipment auctions. The price was good and I have beaten the heck out of it without any problems at all. It is a little large for my tractor, but it had all the features I wanted and it has works really well for me.

 

[NewtoOrange]

EA grapple has 2 pistons, at least the 55". Don't really see any operational difference between the LP and EA.

True for the 55", I was researching the 50" bucket style but decided on the LP which looks almost exactly the same as the EA 55".