Any one know where I can get my hands on this bolt. Original part #03014-50660, SCREW PAN HEAD. Not sure if that’s it. But that’s what was there.
Parts help
- Thread starter Ripp
- Start date
Ace or big box store? It'll be metric, maybe 60mm long. Dealer or Messicks otherwise. Looks like a hex head to me.
That is most likely a JIS hex head cap screw. NAPA or similar should have a limited selection of JIS fasteners
EDIT
Whoops - I spoke too hastily. If that has a cross point recess in the head it would be a SEMS screw - something Kubota uses occasionally. Thats not something you will find at a parts or hardware store.
Dan
Last edited:
North Idaho Wolfman
Moderator
Staff member
Lifetime Member
Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
Definitely a hex head. If you remember my post about the control valve on my B6200…
I broke one of the bolts.. all eight boltsfor the relief cover and but they’re all the same hex head
Messicks and German Bliss don’t have the original pan heads. Messicks says they have the hex bolts.
Last edited:
Already tried Messicks. They don’t have the one heir showing on hand.
Last edited:
While we’re looking at that diagram. #230 as well as #250 are not available Messicks or German Bliss. The spring I can reuse. But the seat is my concern. It wasn’t there when I removed the relief valve to inspect it. Any ideas?
Now THAT's quite a tape measure! Used by seamstresses to measure your inseam!
SHEESH!
Seriously, for the last few weeks, I've been measuring a ton of metric fasteners, washers, and seals. Did a warehouse cleanout of NOS moped parts. The German (Sachs) engine parts are spec-ed down to 0.1 mm. I have a metric calipers and a metric/English tape measure.
So, I'm a tiny bit sensitized by the um, LACK of precision here? OMFG. YGTBKM.
Back to your regularly scheduled programming...
-Paul
Dont over think this.
I think the original fastener is a SEMs screw made to JIS standard. I gave encoutered them in the past. It has a 10mm modified hex head with cross point (Phillips) drive in the center of the head and a caotive underhead washer. Bel Metric sells them but not in that length and they are special order.
belmetric.com
In practice a JIS hex head bolt is nearly identical but without the Philips drive and captuve washer.
belmetric.com
A flange head JIS bolt wont need the washer.
belmetric.com
A metric hex bolt ftom a big box store will be a DIN standard fadtener with a 11mm head.
Thats the technical difference in the fasteners and for all practical purposes this is a tempest in a teapot. Any of those options will work fine.
Dan
I think the original fastener is a SEMs screw made to JIS standard. I gave encoutered them in the past. It has a 10mm modified hex head with cross point (Phillips) drive in the center of the head and a caotive underhead washer. Bel Metric sells them but not in that length and they are special order.
M6X1.0 Hex Phillips SEMS Steel Yellow Zinc, Flat Washer
This M6X1.0 SEMS screw is manufactured, giving you a real metric fastener sized to spec. In stock now at BelMetric, America's metric-only fastener supplier.
belmetric.com
In practice a JIS hex head bolt is nearly identical but without the Philips drive and captuve washer.
M6X1.0 JIS 7-Mark Hex - Steel JIS B-1180
Sourcing metric hardware isn't always easy - this M6X1.0 hex fastener is stocked in steel to JIS 7-Mark spec and ready to ship. Available now from BelMetric.
belmetric.com
A flange head JIS bolt wont need the washer.
JIS Flange Bolt 10.9 Coarse M6X1.0 / 10mm Wrench
Sourcing metric hardware isn't always easy - this M6X1.0 flange bolt is stocked to JIS Flange spec and ready to ship. Grade 10.9. In stock now at BelMetric.
belmetric.com
A metric hex bolt ftom a big box store will be a DIN standard fadtener with a 11mm head.
Thats the technical difference in the fasteners and for all practical purposes this is a tempest in a teapot. Any of those options will work fine.
Dan
Dont over think this.
I think the original fastener is a SEMs screw made to JIS standard. I gave encoutered them in the past. It has a 10mm modified hex head with cross point (Phillips) drive in the center of the head and a caotive underhead washer. Bel Metric sells them but not in that length and they are special order.
M6X1.0 Hex Phillips SEMS Steel Yellow Zinc, Flat Washer
This M6X1.0 SEMS screw is manufactured, giving you a real metric fastener sized to spec. In stock now at BelMetric, America's metric-only fastener supplier.
In practice a JIS hex head bolt is nearly identical but without the Philips drive and captuve washer.
M6X1.0 JIS 7-Mark Hex - Steel JIS B-1180
Sourcing metric hardware isn't always easy - this M6X1.0 hex fastener is stocked in steel to JIS 7-Mark spec and ready to ship. Available now from BelMetric.
A flange head JIS bolt wont need the washer.
JIS Flange Bolt 10.9 Coarse M6X1.0 / 10mm Wrench
Sourcing metric hardware isn't always easy - this M6X1.0 flange bolt is stocked to JIS Flange spec and ready to ship. Grade 10.9. In stock now at BelMetric.
A metric hex bolt ftom a big box store will be a DIN standard fadtener with a 11mm head.
Thats the technical difference in the fasteners and for all practical purposes this is a tempest in a teapot. Any of those options will work fine.
Dan
I think this is what i pulled out of there.. Whats throwing me off is the heads of these bolts where painted like they were installed OEM from the factory. But they are def not pan heads.
Last edited:
North Idaho Wolfman
Moderator
Staff member
Lifetime Member
Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
I think your getting hung up on the part name:
And yes Kubota manuals and descriptions gets the part name wrong some of the time.
Front cover bolts: 01202-50655
BOLT M6x1.0x55 mm
Rear cover bolts: 01202-50660
BOLT M6x1.0x60 mm
And yes Kubota manuals and descriptions gets the part name wrong some of the time.
Front cover bolts: 01202-50655
BOLT M6x1.0x55 mm
BOLT M6x1.0x55 mm
www.hoober.com
Rear cover bolts: 01202-50660
BOLT M6x1.0x60 mm
BOLT M6x1.0x60 mm ***
www.hoober.com