New Attachment For My L2501

[fenderbender]

Just went and picket up my tractor after have a BH77 backhoe put on. Ground is to wet around here to even try it out now. Also got a tiller and spreader too.

Sent from my P00I using Tapatalk

 

[mic214]

That is a great looking rig. I like your trailer set up too.

 

[fenderbender]

That is a great looking rig. I like your trailer set up too.

Thanks

Sent from my P00I using Tapatalk

 

[Stomper]

Sweet setup. How much is involved in removing the back hoe to use you 3ph equipment

 

[North Idaho Wolfman]

FYI:
If you move it again you need to have 4 chains on the tractor, one on the loader, one on the Back hoe, and one on any other implement on the trailer to make it legal.
I got pulled over by a GA Trooper years back and read the riot act, even threatened to impound me for not having it tied down properly.

 

[fenderbender]

Sweet setup. How much is involved in removing the back hoe to use you 3ph equipment

It seems like it won't be too bad after the first time or too.

Sent from my P00I using Tapatalk

 

[fenderbender]

FYI:
If you move it again you need to have 4 chains on the tractor, one on the loader, one on the Back hoe, and one on any other implement on the trailer to make it legal.
I got pulled over by a GA Trooper years back and read the riot act, even threatened to impound me for not having it tied down properly.

I live in a small area and been trucking for 40 years in and out of here I know all the DOT around here. I asked and they said if I'm just moving it from one of my properties to another and not getting paid I'm fine. If doing for hire I will get bothered. I know what the regs say but that is one advantage of being from alittle small community.

Sent from my P00I using Tapatalk

 

[quicktractor]

Very nice!!!!

 

[Fro65]

You are going to love it. Handiest shovel I ever bought. Despite dealer and everyone else trying to talk me out of it. Nice tiller and spreader too.

 

[quazz]

It seems like it won't be too bad after the first time or too.

Sent from my P00I using Tapatalk

It isn't too bad unless you do what I did and set the backhoe on uneven ground where it proceeded to sink even more unevenly. It was a pain in the butt getting it back on today.

 

[fenderbender]

It isn't too bad unless you do what I did and set the backhoe on uneven ground where it proceeded to sink even more unevenly. It was a pain in the butt getting it back on today.

They told me to make sure it's level and hard ground

Sent from my P00I using Tapatalk

 

[quazz]

They were right. absolutely right.

 

[North Idaho Wolfman]

I know what the regs say but that is one advantage of being from a little small community.

Yea I hear ya, it's similar up here.

 

[Tunaslayer]

If you have a garage, look into a dolly for the back hoe. Makes hooking back up very easy.


Sent from my iPhone using Tapatalk

 

[fenderbender]

Got to try out the new hoe today. Thought it did good seeing as how I haven't been on one in about 25 years. One thing I'm going to have to make something to slide the seat further back. Need more leg room.

Sent from my P00I using Tapatalk

 

[Tunaslayer]

You can raise the seat. That helped a little, but I agree. It’s cramped.


Sent from my iPhone using Tapatalk

 

[fenderbender]

You can raise the seat. That helped a little, but I agree. It’s cramped.


Sent from my iPhone using Tapatalk

I'm going to move towards the steering wheel with some angle iron just as soon I get time

Sent from my P00I using Tapatalk

 

[Tunaslayer]

There is a post somewhere about this. They used aluminum angle to shift it. Post some pics when you are done! Wanna see the Mod.


Sent from my iPhone using Tapatalk

 

[fenderbender]

There is a post somewhere about this. They used aluminum angle to shift it. Post some pics when you are done! Wanna see the Mod.


Sent from my iPhone using Tapatalk

That's kinda what I was thinking. I'll post pics when I try it out

Sent from my P00I using Tapatalk

 

[fenderbender]

That's kinda what I was thinking. I'll post pics when I try it out

Sent from my P00I using Tapatalk

Here's the pictures. 2.5" x 3/8" thick. 1/4" would probably worked just as good. Going to round the edges just was making sure that was what I wanted

Sent from my P00I using Tapatalk