Attachment Hydraulic Hose Pressure Relief

retiree-urgency abandoned

Member

Equipment
B3350, Kub. 5" rotary cutter, LP 48" forks, Titan Aerial Platform, KK XB Dump
Dec 1, 2020
90
97
18
Bloomington, IN
It's nice & hot which means the hoses on attachments are pressurized and tough to connect to the tractor. In other threads, it seems that if you connect the 2 hoses on the implement to each other when you take it off the tractor, the pressure is less or not a problem.

My attachments are plumbed with male fittings - female fittings on the tractor, so I was thinking of assembling some female-to-female fittings to connect the attachment hoses when not in use. After more thought, would it make more sense to connect 2 female fittings to a T pipe-nipple and add a valve to the 3rd leg to drain pressure?

Just trying to make life a little easier when switching attachments.
 
  • Like
Reactions: 1 user

MapleLeafFarmer

Well-known member

Equipment
Lots incl. B and L kubotas
Dec 2, 2019
782
678
93
E.
or .... when you unhook a hydraulic attachment just push the plunger/poppet of both fitting with a ragged hand.
A small amount of fluid may come out.
This helps prevent problems when re connecting in hotter weather.
Quick, easy, and cheap.
 

North Idaho Wolfman

Moderator
Staff member
Lifetime Member

Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
Jun 9, 2013
33,389
8,700
113
Sandpoint, ID
If you connect the two hoses together, they can't build pressure so no need for a tee, but if
it makes you feel better have at it!
 
  • Like
Reactions: 1 user

Old Machinist

Well-known member

Equipment
Kubota LX3310 cab, JD 4310, NH 575E cab backhoe, JD F725, Swisher 60", etc.
May 27, 2024
377
397
63
NE FL
I only have one implement with a connection being my grapple. My hoses are zip tied together so I can't connect them to each other. I have thought about switching to the connect under pressure flat face but then realized I don't have any need. I just push the male poppet against the frame of the grapple to relieve the pressure before connecting. I use the rubber caps and plugs to keep the dirt out but I still have to clean them with paper towels before and after. I keep a roll in the ammo box I mounted on the tractor.
 
Last edited:
  • Like
Reactions: 1 user

nbryan

Well-known member

Equipment
B2650 BH77 LA534 54" ssqa Forks B2782B BB1560 Woods M5-4 MaxxHaul 50039
Jan 3, 2019
1,302
825
113
Hadashville, Manitoba, Canada
I now have handy now a hammer, round-faced drift (sized to be a snug fit in fitting), and a rag, for when those connectors refuse to snap together. Increased temperatures after the removal from the tractor has had these things really tightly sprung sometimes. Wrapping the fitting with a rag as a safety and cleanliness thing, the released oil can spurt rather forcefully everywhere.
 

Russell King

Well-known member
Lifetime Member

Equipment
L185F, Modern Ag Competitor 4’ shredder, Rhino tiller, rear dirt scoop
Jun 17, 2012
6,355
2,011
113
Austin, Texas
If you connect the two hoses together, they can't build pressure so no need for a tee, but if
it makes you feel better have at it!
A sealed system can build pressure if the fluid temperature increases due to thermal expansion. A pressure cooker is an extreme example of that.

Connecting the two lines together will ensure the pressure equalizes through the system but it can increase.

If there was a short empty hose between them that would allow the fluid to compress air in the short hose which may help but eventually that short hose would be full of compressed air and hydraulic fluid unless it is drained out occasionally.
 
  • Like
Reactions: 1 user

JonM

Active member

Equipment
Kubota Grand L6060
Nov 29, 2024
76
136
33
wisconsin
if your hydraulic fluid is at a good operating temp before you disconnect it will be easier to reconnect when it cools.

for example if you have a grapple attached but didnt really use it cycle it a few times so the fluid has a chance to changeover before disconnecting it. the warmer fluid will contract a little as it cools making a later connection easier even if the ambient is warmer.
 

edritchey

Well-known member
Lifetime Member

Equipment
Ferris IS800Z - New Holland WM75 - John Deere X500
Jul 19, 2014
1,117
819
113
Wellsville, PA
It's nice & hot which means the hoses on attachments are pressurized and tough to connect to the tractor. In other threads, it seems that if you connect the 2 hoses on the implement to each other when you take it off the tractor, the pressure is less or not a problem.

My attachments are plumbed with male fittings - female fittings on the tractor, so I was thinking of assembling some female-to-female fittings to connect the attachment hoses when not in use. After more thought, would it make more sense to connect 2 female fittings to a T pipe-nipple and add a valve to the 3rd leg to drain pressure?

Just trying to make life a little easier when switching attachments.
If you put a 3 way valve on one of the lines on your grapple you can crack it open to relieve the pressure prior to connecting the lines to your tractor. I also like to connect them together like Wolfman already mentioned pressure will still build up especially if the attachment is sitting out in the sun but the 3 way valve will take care of that problem. Here is a link to a good one. Click Here
 

Schmitty

Member

Equipment
L4740, grapple, forks, box blade
Mar 25, 2018
58
23
8
Madison, WI
If you put a 3 way valve on one of the lines on your grapple you can crack it open to relieve the pressure prior to connecting the lines to your tractor. I also like to connect them together like Wolfman already mentioned pressure will still build up especially if the attachment is sitting out in the sun but the 3 way valve will take care of that problem. Here is a link to a good one. Click Here
This is what I did, but I put it on the tractor side, as that's where the pressure comes from. Then the grapple gets connected together...if I can muscle them together when I take the grapple off. :LOL:
 

PoTreeBoy

Well-known member
Lifetime Member

Equipment
L35 Ford 3930
Mar 24, 2020
3,221
1,831
113
WestTn/NoMs
A sealed system can build pressure if the fluid temperature increases due to thermal expansion. A pressure cooker is an extreme example of that.

Connecting the two lines together will ensure the pressure equalizes through the system but it can increase.

If there was a short empty hose between them that would allow the fluid to compress air in the short hose which may help but eventually that short hose would be full of compressed air and hydraulic fluid unless it is drained out occasionally.
In theory, IF the cylinder is not fully extended to start with, the total volume of the cylinder can expand by extending slightly. This will allow the fluid to expand without building pressure.

But the two hoses have to be coupled together, otherwise you have two closed systems and the piston can't move. The pressure on the rod end would be higher than the other end But by coupling them together the pressure equalizes and the rod extends slightly.