What did you do to or on your Kubota today?

GeoHorn · Jun 2, 2020

SidecarFlip said:
You know they are washable? I soak mine in a bucket with Dawn dish wash detergent, rinse in clear water and let air dry. beats 35 bucks for a new one.

I cleaned mine this week also. I blew it out with compressed air and it looked good enough to re-install... but reading the manual saw it was washable so I stuck it in a 5-gal bucket with Dawn and it turned the 3 gallons of soapy-water absolutely BLACK! I did it again with fresh water and it got that pretty dirty also.
Anyway, I know they say not to, but I also blew out the secondary but nothing came out of it so I reinstalled it after wiping the entire filter-box/cylinder out with a damp rag.
It’s surprising how much dirt these things capture even when you think you’re using the tractor in a non-dusty environment. Lots more air goes thru a tractor than fuel so I think its a good idea to keep up with these.

sparky45 · Jun 3, 2020

Disk'd up some ground I plowed a few weeks ago, gitt'n ready to plant a food plot for the Quail ( hopefully they'll stop by). Sorghum Millet mix.

Tbucket32 · Jun 3, 2020

New shed is almost done. Power goes in this weekend and floor pour in a couple weeks

Sent from my SM-G975W using Tapatalk

RCW · Jun 3, 2020

Tbucket32 said:
New shed is almost done. Power goes in this weekend and floor pour in a couple weeks

Dayum.....

All I got to say.....except I’m very jealous....[emoji15]

Sent from my iPhone using Tapatalk

Magicman · Jun 3, 2020

Wowser Tbucket32, that is much more than a "shed"!!

BX23S · Jun 3, 2020

Tbucket32 said:
New shed is almost done. Power goes in this weekend and floor pour in a couple weeks

Sent from my SM-G975W using Tapatalk

Wow! Big enough to live in.

Any interior pics?

Tbucket32 · Jun 4, 2020

26x32...12ft walls.
Inside is bare. No plan to finish the inside any time soon.

Sent from my SM-G975W using Tapatalk

fj40dave · Jun 4, 2020

Spread 5 yards of 3/4 minus for a concrete driveway base yesterday....
Hey....keeps us busy!!!

Rosher18 · Jun 4, 2020

Spread 31 tons of 3/4 minus to bolster up our arena parking area and start a road from there to my shop roll up door. (road will be under pile when done)

Sent from my SM-G960U using Tapatalk

Lil Foot · Jun 4, 2020

(road will be under pile when done)

Well thought out. I'm always amazed at the number of folks who don't do this.

BX23S · Jun 4, 2020

Finally received OEM oil filters, fuel filters and air filter.
Installing the engine fuel and air filters was a piece of cake, however, the rear fuel filter remains a pain in the arse, my hands are too big, as such I cannot get to the bottom hose clamp. Does anyone have an easy way to removed it? TIA!

Tbucket32 · Jun 5, 2020

This was dug by a CAT, but my little B7500 will be filling it all back in once the conduit and cables are installed.

Sent from my SM-G975W using Tapatalk

fj40dave · Jun 5, 2020

Spread a little gravel around today.....nothing big, but that's what we were up to today with the B2650

mdhughes · Jun 6, 2020

Did a little clearing on the private road frontage, trimmed tree limbs hanging over the road and chipped the up.

It's been a while since it has been dry enough to get the chipper out of where I store it to use it.

edritchey · Jun 6, 2020

mdhughes said:
Did a little clearing on the private road frontage, trimmed tree limbs hanging over the road and chipped the up.

It's been a while since it has been dry enough to get the chipper out of where I store it to use it.

What chipper do you have for your tractor?

mdhughes · Jun 6, 2020

It is a WoodMaxx WM-8m. I have had it since June of 2015. It came in handy when we took out 16 trees to put our garage in. Chipped up all of the tops, had two piles that were around 4' tall and a couple smaller ones. A friend took most of the chips to use as mulch.

It weights 950 pounds, has a 24" 200 pound flywheel with 2 knives. Infeed opening is 8" x 8".

I have been very happy with the chipper.

edritchey, you will notice I got the bucket level indicator on the loader. Took me about a year to get it on the tractor.

Chilliwack Murray · Jun 6, 2020

Built a new pad to repurpose the greenhouse as a garden shed, rotated 180 degrees and moved into its new spot.

It was over a couple days though.

Bmyers · Jun 7, 2020

Spent another Saturday at the farm. We got 40 acres of beans planted. Worked on clearing more around the well house and hauling brush to the pile.

Still have more work to do, but it was getting hot and was time to stop for the day.

fruitcakesa · Jun 7, 2020

Moved some big base stones to the wall project that I started over in the projects forum and that continues

SidecarFlip · Jun 7, 2020

Cut hay, will be running hay all week....

What did you do to or on your Kubota today?

Well-known member

Active member

New member

Well-known member

Well-known member

Member

New member

Well-known member

Attachments

Member

Well-known member

Member

New member

Well-known member

Attachments

Well-known member

Attachments

Well-known member

Well-known member

Member

Well-known member

Attachments

Well-known member

Attachments

Banned

Attachments