Search results

I did get one off a 9200, the gearbox bolted right in, the column was an inch shorter but it fit. I did have to use my pitman arm as it was longer than the one from the 9200 which had clearance issues.

Thanks for all the help Gary, I appreciate it more than you know, I sent you a PM with the information we talked about. Thanks so much for everything Eric

Hi Gary, tried to call a few times, busy and now says cant be completed as dialed, tried your cell as well, left you a message, I was out on the road but am home now

I just did some digging Gary, that gearbox is for a B9200 with a serial number under 52071. The drawings look identical and they do use the same bearings gaskets and o-rings but the rest of the parts are dif numbers. Can you get some measurements off of it? If its close and will bolt in I would...

Parts diagram shows mine is a 66301-41100.... so close, thanks for checking the part numbers Gary

Still looking, Gary wasn't sure if his was the right part #, thanks for checking Gary.

I am in search of a working used steering box for a B8200HSTD, mine broke over the weekend moving dirt and the parts I need to repair it are no longer available, so does anyone have a used one available?

Been plowing snow and more snow and more snow, I have no wind break to the west and live on top a hill so even on days it doesnt snow I get drifts across the drive, I guess I need to put up a snow fence one of these winters and see if it helps. Kubota has been firing up great since the glow...

Well its been about 5 months since I did the tire swap and I can say, in my experience, this has worked out well. The tractor has spent more hours than I can count in 4 wd, moved 120 tons of bank run fill, 60 tons of #57 crushed rock, dug out and leveled a base for a new storage building, 20x16...

Well I changed out the glow plugs on my B8200, starts much easier now, it was already hard starting on 30 degree mornings, so it was time, made a set of skids for the box scraper for snow plowing the driveway this winter, finally got lights in the barn addition (kubota's home). been a busy...

Got in 120 tons of bank run fill over the last 2 days, got it all moved and spread and started leveling it, still need to do some more leveling with the box blade but the rain came in yesterday and ruined that plan, hopefully it dies out over this next week and I can get it done, more rain...

Drilled the last few post holes, put the box scraper back on, started breaking up sod and digging out the topsoil so I can put down a good base for the stone thats going between the garage and barn.

Well I found the culprit, problem is its sure not an quick easy fix, every linkage from the pedals to the trans is junk, the links are fine but all the plates instead of having round holes have oval holes, there is so much slop in the linkage that when the roller bearing centers itself in the V...

Thanks all, I have a service manual but it was loaned to a friend, got it back today and tore into it this evening, even with the pedal assembly and swash plate removed, the inverted V doesn't return to center and it creeps, I ran out of daylight tonight so I will dig back into it tomorrow, the...

Ok, so I have been dealing with this issue since I got the tractor and until now its been livable, but digging post holes over the weekend it really got to me, the pedal for forward and reverse on my HST doesnt return all the way to the middle when you let off of it, so it tries to keep creeping...

Drilled 12 post holes over the weekened for the new fence, only broke 1 shear bolt but did get it stuck a few times, the 3 point hydraulics just didnt have enough power to pull it out without rocking the tractor a little, then it popped right out, ground was hard and dry and lots of rocks, I am...

Thanks for the insight, I moved the links earlier today and it does seem to be a lot more managble lifting it while drilling holes. Doesnt seem to want to get stuck as quick :)

I have 2 holes in the lower arms of my 3 point on my B8200 HST 4wd, which hole provides the most lifting ability, the lift links are currently in the holes closest to the tractor, while digging post holes I find it has a hard time pulling the auger out of the hole when drilling the holes, will...

I see your over in Tallmadge, I am out in Ravenna, I picked up my R4's at Terry's Tire Town in Alliance, they have an AG/Commercial building out behind the warehouse, might want to give them a call and see what they have available in your size, they may even have some used ones, never know. As...

Went to tractor supply and spent some money..... picked up a 5' box scraper and a 3 point post hole digger with a 9" auger, got home and used the FEL on the Bota to unload them and put them away, hope to get the post hole digger mounted in the next few days and start drilling some holes for...