Search results

Yes I’m using UDT2 if needed but hopefully most of what I take out goes back in. On my model M5091, the filters are located on the right hand side of the gearbox, so I would have to tilt the tractor to the left, not lift the front. What is involved to pull a vacuum and does that stop any oil...

Hi. I have an M5091 due to change hydraulic filters but not the oil, as per scheduled service interval. I’m hoping to do this without having to drain and refill the 60l of oil and with as little mess and spill as possible. Does anyone know an easy way to do this or at least how much I need to...

Hi. I have a 200mm 8bolt clutch on a 7ft slasher. The problem I have is after a while, usually when I replace clutch discs, some of the spring bolts will seize up and cannot be unscrewed. Need to be cut off. Is this a common problem and what is the cause and any solution? Thanks

Hi. I have a M5091 with no front weights at the moment. I'm looking to pull an average sized 4 furrow plough around. Was wondering if and how much weight I would need on the front to keeps things pulling nicely? Thanks.

My lever for moving the rear 3 point linkage on my M5093 is a little stiff in movement for my liking. I’ve followed the cable to the pictured spring/ arm. Was wondering if loosening the 2 screws on the spring would give a less stiff lever movement? If not, what else could I do to soften the...

You should try using it, your missing out. I actually rarely use the lever and just use the memory button. It's like using the lever but better. You can get back to the exact revs you were using every time you throttle up much quicker and easier. It's more precise with rev setting as well as...

On my M5091 if you want to set the automatic revs button, the revs slider lever can't be all the way low. It needs to be up at least a little bit forward. Is there any way this can modded so that I can set the rev button with the lever at full low? At the moment I bush the lever up a mm or 2 and...

The tires and incorrect configuration are how it was delivered to me. Yes, dealer needs to fix the problem.

Just a follow up on this. Iv'e since learnt that these tractors need the front wheel width set using dish and rim orientation, depending on what size tires are fitted. The rims are offset, and in my case they were the wrong way around for my size tires, so the rims were turned around and swapped...

I've burnt a few PTO clutches recently slashing extra tough grass. The main reason for the burning up is not realizing soon enough that grass is not being cut and the clutch is slipping. Sometimes I don't notice until about 5 -10 seconds of slipping. If I would lift the slasher or stop the PTO...

I learnt something today.

Hi. Are you saying my problem is caused by an unbalanced shaft? The shaft runs smooth and does not noticeably vibrate. I’m only guessing the enlarged slot is from forward and back movement. I don’t know what caused it.

The shaft center joint tube did not have enough grease at one stage, was dry. Could that cause it?

Haven't asked the dealer yet. Standard tires and rims set to their widest. (Edit- I've since learned that the spacers were set to their widest but rim orientation was not.) There looks to be plenty of negative camber and wheels are toeing out. Flat ground there is no problem. It happens on...

See attached picture. New M5091 front tires rubbing on bonnet when turning full lock and terrain is bumpy. Is this normal or is something out of alignment? I'm thinking of cutting down the inside edges of the front tires treads. Thanks.

Hi. I'm running a 7ft slasher on a 93HP Kubota. The male part of the PTO shaft has a slot that the pin of the uni join goes through when connected. This slot has worn on the one tooth that the sliding pin goes through when connected, causing the surrounding area to enlarge and then the uni...

Yes, I’m planning on doing that. thanks.

What the factory put in from new. Tractor is under 50 hours.

Hi, thanks for the reply. I have to partly disagree with you that I should be using the shuttle control to start and stop. Yes it is practical to use it sometimes such as in open spaces, but in any kind of movements close to something or if you need small amounts or a slow movement you have to...

Hi. I have a Kubota M5091. I'm liking the tractor except for the clutch performance. The take up when releasing the pedal is too fast/ sudden. Because of this, it is very difficult to take off smoothly without jerking forward like you are just learning to drive a manual vehicle. This tractor has...