Hi all,
This is verry strange (to me) It has a loss of overall power, and wanting to stall. It will idle fine at low or high rev, (this is a hydrostatic machine), But shifting into either high or low range it sputters and wants to stall, but shifting back to neutral position it returns to a...
I can't find the weight of the BH-70 back hoe in the assembly or op. manual, What is the weight of the detachable assembly?
I do not have ballast in the rear tires, (and Kubota does not recommend ballast AND back hoe together) so when removing the hoe, I want to add a ballast box of equal...
Should this be done? or is that too much rear weight?
Currently have the BH70 on my 2301, and no ballast in the tires, But don't ya need ballast when running the loader only?
Hi All Picked up a B2301 TLB with 18 hrs on it.
Was using it today for about 4 hours constantly with no issues. then while moving a load of spoil with the bucket, In low range, pressed on the forward pedal and the engine shut down, took my foot off the pedal and the engine came back to life...
Looking to add a reverse light switch so, just like a vehicle, rear lights only come on when in reverse, on off going forward. HST direction pedal offers its own challenges to this.
Any Ideas?
Thanks
Reamer
Hi all
First time using the BX-1500 and BX2750C snowblower, Unfortunately the Driveshaft (from mid mount pto to the Quick hitch) decided the snap a U-joint and take an ear with it. I can't find a parts diagram or part number for the drive shaft...
Can anyone help on the p/n?
Thanks
Reamer
2 cylinder BX1500, where to tap in for cab heat
I've been watching Ping's home made cab for his BX, Gonna start one for my BX1500, being smaller and a 2-cylinder instead of the common 3 cyl, where can I tap in for:
(A)Flow to the heater, and then, (B) return from heater to the tractor.
Thank...
First year with the BX1500, No whining with MMM all summer, Installed a Hydraulic system and valve, drained and filled with super UDT, Plow works wonderfully, and reacts quickly, but the system "whines"
Is this normal?
Thanks
reamer
A friend has a late 80's early 90's B-7200. Came with a RC60-72 deck.
Older style with front cable-activated PTO, that then powers the driveshaft.
The deck body is completely rusted through, Spindles, pulleys and bearings are fine, but needs a new body.
Thanks
It appears Kubota does not sell the shaft by its self, only a new gear box "assembly" for $472.00.
anyone try to take the "slack shock" out of this, this is what maybe breaking the shear pin, since it is so sloppy..
I have a B2660 front mount snowblower complete with subframe and driveshaft. Currently the subframe is still mounted on my B-2400.
Runs fine... Will send you photos....
$2700.00
Ron
I have the BX1500 HST, According to the manual, it reads, "position at 1/2 throttle and activate the PTO lever". after a second it "slams" into gear, kinda shaking the tractor.
On my B-2400 HST I have a "clutch" pedal and can activate the mid PTO and gently by letting-off the clutch pedal.
But...
I know they say "compatible with all BX tractors" but in actuality are they?
I know with the "BX quick hitch" there is one only for the BX1500, this rests on the frame and secures with a large "T" screw and every other series BX uses a different type that "bolts" on....
Is the BX 2750C...
Hi All
This is on the left side of a BX1500, this hole has a bolt welded to the other side.
it is used for the "hold down" plate for hydraulic lines.
I am installing the lines for a plow, I have the plate just need to find out the pitch/size bolt to use here.
Thanks!