Search results

I have parts to replace the front end seals on a L3000DT. Not sure what else they fit. Brand New, Still in the original package. 2 - 04811-10850 O-Ring 2 - 31353-44130 O-Ring 2 - 37650-43530 Seal, Oil 4 - TC010-99600 Assy, Seal Cost $310.00 Will sell for $100.00

I have a new set of blades kubota # 70000-25023 or 60250-80270. Not sure what they fit, but will sell for $30.00 for all 3. 18 3/8 inch long, 2 1/2 inch wide, 1 1/8 hole in center.

i have a brand new, still in the box, radiator for a L3000DT. I am not sure what else it fits, but the part# TC020-1600. List Price $596.36. Will sell for $200.00

I have some brand new parts for a l??? kubota, that I would like to sell. I got the part #s but not sure what they fit. Is there anywhere that I can lookup the part# and it will tell me what kubota that they fit? Thanks

I need to replace my ujoints on the front drive shaft of my RTV900W 2005 serial # 31307. Kubota says I have to replace the entire drive shaft. Has anyone purchased just the ujoints and do they have a part #? Thanks

I am looking for hard cab for my 2005 RTV900w. Does anyone know where I can get one? Thanks

I have a b71hst with 4 wheel drive. I know how much grease/oil that the front and rear diff should have. How do I check it to see if it has enough without draining and refill? Thanks

I have a mr4800 mower and have broken 1 blade. The blades that kubota recommends will not fit. Messick is trying to find the correct blade, but so far has had no luck. Does anyone have any info? Kubota says the blade is Part # 70000-25006, but it is 20 1/4 inch long and has no alignment holes...

I have a b7100hst-d. when I purchased it, it had a toggle switch for the lights. I am in the processes of rebuilding it. I purchased the stock light switch from kubota and was expecting to find connection screws on the back. There are no connection screws. It does have copper "ports". I am...

Does anyone have the sheilds for a MR4800 mower deck? Part # 70721-41130 and 70721-41150. Thank...

Does anyone know how to remove the belt pulleys on a mr4800 mower deck?

I have a b7100hst that came (uninstalled) with a mr4800 belly mower. I am not sure on how it hooks up with the 3 point hitch. Does anyone have a picture of a b7100hst with the belly mower installed? I just need the back where it connects with the 3 point hitch. I am not sure if I am missing...

Anyone have any suggestions what to use to line up the transmission spline on a b7100hst. I removed the engine to rebuild it and am ready to install the clutch and pressure plate. Thanks

I am putting back on the timing gear case cover on my b7100hst and noticed that there are 4 different size bolts. The manual and messecks show where 1 of each go, but not the rest. does anyone know where each size bolts go where? Thanks...

i removed the pushrods on my b71hhst, and di not take any pics, because I do have a service manual and Kubota part diagrams. I have the 6 pushrods and 6 caps. in all diagrams they do not show the caps. can anyone show me whre the caps go? they look like they go at the bottom of the pushrods...

I am rebuilding a b7100HST. When I ordered new 12 Head bolts,2 studs and 2 nuts for the studs for this engine, The head bolts and studs were in reason, but the 11MM nuts were $23.00 EACH. At first I thought it was a mistake and called 2 Kubota dealers and they said that is the correct price, but...

I am rebuilding the engine in my B7100 HST D (old). The rebuilding gasket set and parts diagrams in the shop manual show a shim for the head gasket. I cannot find anywhere that explains if or when you should use the shim. Anybody have any definite info on this shim, when or if you need it...

I just purchased a b7100 HST. It is blowing a lot of smoke. I am going to do a compression test. Has anyone done a compreesion test on a B7100? If so what are the steps. I have a compression tester, Do I go through the glow plugs ( seems like I have to remove a lot of parts to get to them) or...

I went to purchase parts for my B7100HST That I just purchased and they want to know if it is the "old type" or "new type". How do I tell which one I have? SN B7100HD11900 thanks