Search results

When using the 3 point on my tractor the 3 point constantly drops, and I have to keep bumping the lever to keep it at the height I want. I also notice the lever tends to spring forward to the drop position when the arms get to a certain point. Also, if I take the 3 point to the full up position...

Any one use these? Ebay Link One of mine has been broken for a very long time. I haven't measured mine to see the length differences. And I can't find any information about the eyebolt thread diameter or the pin diameter so that i know if these will bolt in without modification.

As stated in the subject Im just about finished rebuilding a d722 diesel. The owner ran amsoil full synthetic 15-45 diesel oil in it and gave me some after I get it done. I've heard it takes longer to break in an engine on full synthetic. Is there any truth to that. Should I ho ahead and use...

I don't have a service manual for this engine. I did however find a manual online that i could look at. That manual pic below states its supposed to have a torque of 13 to 15.9 ft pounds which seems like a lot. I looked in the manual I have for my D950 and it is like 9 ft pounds tops. Can...

I've been looking through the parts book for the right part. I'm looking for the part that stops the control handle for the 3 point from dropping all the way down. should be some sort of bolt and wing nut thing I think. I can't for the life of me find it. One would think it would appear where...

I just got my mower deck(RC60-72H) mounted on my tractor and tested it for the first time. I realize this is used and its bound to make some noise. It has a decent amount of whine to it. Since I have no prior experience with these mowers I don't know what it should have sounded like if all the...

My hour meter has 3 black numbers and a white number. Is the white 10ths or hours? I'm thinking hours but i'm not sure. There are two tractors on ebay that are showing super lower hours, like 125 and 200. but it has those numbers in the black and a number in the 10th. and if it is 10ths how...

I'm still new into this little tractor i got last year. I acquired a kubota mid mount mower deck and i'm going to put it to work. I was wondering what others do when they use the rear pto to stop from spinning the mower. I haven't tried putting my mower deck on yet, I'm a long ways from that. It...

I finished my engine rebuild and re-installed the engine.(runs great again:D) I noticed that the input shaft of the front axle is resting on the oil pan. Is there any kind of fix for this? I haven't got to look at it in depth yet, Just wondering if anyone else has experienced this and how they...

I'm just about done my rebuild on my d950 for my b7200. I bought rotella 15 40 for it. I noticed in the manual it calls for 10 30 and was wondering what everyone else runs. Is the travelers brand hydraulic fluid OK for the hst transmission.

I bought a full engine gasket kit from Kumar bros. Been a lot of issues with this gasket kit, incorrect orings and seals, missing stuff.... It came with two head gaskets, one regular gasket, and a peice of flat steel in the shape of a head gasket. What is the flat steel gasket for? Do I need...

Has anyone ever had a failure with the oil pump on a d950 engine? I'm in the middle of rebuilding my engine due to a connecting rod bearing failure. My low oil pressure light did not come on when when you turned the key to the on position with the engine off so i figured there was probably a bad...

Dup Duplicated.

It looks as if soon i will be ready to buy an over haul kit for the d950 in my b7200HST. If all goes well it will be standard size. Where's the best place to get the best kit at the best price. I'm going to call Messicks and see what they want for what i need. From what i see i need gaskets...

I recently picked up a RC60-72H mower deck. I got it less the brackets it hangs from. I do have the brackets for the 3 point and managed to aquire the front mounting brackets. but I need the rear brackets and pins. I might be interested in a full bracket set if the price is right.

I recently located a RC60-72 mid mount mower deck and tractordata.com says it will fit my B7200. I just wanted to verify with the kubota community before I go after this. It apparently came off of a B6200. It appears that all the brackets are there for it. Though I have no idea what brackets are...

I got this tractor for free, it ran but had a noise, diagnosed the front piston had slop so I pulled the pan and found the bearing gone on the rod, I haven't decided that the engine is junk yet, but I am actively looking for a replacement until i tear it down over the winter. Does any one know...

B7200 4x4 Hydrostatic question I was given a B7200 Hydro 4x4. Apparently it had a noise in the engine, described as a possible rod knock and was parked. It has never been really checked. I have not heard the noise yet and I need to go pick up the tractor. On my 318 deere there is a valve you...