Search results

8x20 sounds good but 8x30 goose neck would really be nice.

Keep in mind when you go to look at trailers that a 7000 lb rated trailer won't really haul that much weight. You have to factor in the weight of the trailer as well. A 16 ft double axle normally will weigh 2000 to 2500 lbs empty. Another words your BX would put it at above 2/3 capacity. I...

I mounted a small tool box to the right side fender. Also works nice for a arm rest.

This will fix what you right up. Works like a champ. If you can get a straight shot at the ball on the fitting this will grease it. It just slides straight on and then locks in place. I ordered mine from www.thetoolwarehouse.net for about $9.

If my oil was dirty enough to need changing at 20 hrs I would be wanting to know what was wrong with my engine. At 20 hrs my oil still looks like it did when I poured it in.

I agree. PTO equipment is designed to operate at the rated RPM so they will work properly. If you run at a lower rpm you are not only lugging the tractor engine but also putting unwanted strain on the emplement as well. The main thing to remember no matter what the task at hand is not to lug the...

Since the front end is geared just a little higher than the rear is the 4WD is kind of in a bind a lot of the time. My tractor seems to come out of 4WD better if it is moving and I cut my wheels to the right. I never even try to take mine out with the wheels in a straight line. If it's to where...

Amsoil Heavy Duty Diesel 5w30 for your Kubota. Amsoil Synthetic motorcycle oil 20w50 for your Harley. I run Amsoil in everything from my R/C cars to my M 9000. Two stroke, engine oil, trans fluid, trans/hyd oil, gear oil, gas treatment, spray lubricants and protectants, filters and grease. I...

The only place that can happen is where the engine drives the hyd pump. If the seal is bad it's possible for the fluid to transfer.

It's possible. If the engine is overheating it may be causing more than a normal amount of oil vapor to go to the breather and then when it cools done as it's coming out it will change back to a solid state (oil) and run out causing all your mess. You need a good clean radiator anyway so it...

Have you washed the radiator out good? Sometimes they are a real pain to get all the dirt out of them.

I think that Kytim is right. I think that a couple of lights would be fine. If you want to double check it before you mount them get a volt meter and check your battery with the engine off and no current being drawn from it so you will have a base line to go by. Crank the tractor and check it...

Thankyou handy, That is the one I was sitting in when I was on the phone with you yesterday. I really do love that tractor. It sure is a lot better in the field than my other one with no cab.

As long as you don't have any leaks I wouldn't worry about it. Like Eric said it's always much safer to lower everything to the ground anyway.

I never did understand why some people treated the MSHA man like the enemy. It never did make good sense to try and hide problem areas from them. If the company wouldn't allow us to fix the problem you better believe that I would point it out to inspector that was there. For some reason it...

Neat looking setup. I wonder how hard it would be on the 3pt? It is sort of like mine but all I have to do is pull mine and it supports it own weight. It doesn't like mud very well but in regular dirt it works like a champ.

Hello skeets, I have had the pleasure of dealing with a bunch of your Georgia MSHA brothers over the years. I bet you don't hear MSHA and pleasure used together very often but I always looked at it like this. You are just doing your job and if I am doing my job properly then you or me either...

That was lucky to have rain that close and you not get any. I bet It was close enough that you could smell it in the air. I ned a wind guard for my baler and so far haven't been able to find a old baler sitting around anywhere. My baler has the auto weive feature on it but it will only work...

Nice looking baler Mountaindoc, Yours was a Hesston, mine was a M&W. Every time I baled with it my hope was either to break down early enough to order parts before the dealer closed or to break late so I wouldn't feel to bad about having to quit early. One way or the other it was going to break...

I have been around several different Kubota tractors of varying sizes and they all sound different. I have never seen one that didn't make some sort of whining noise. My M doesn't whine to much but it has a rattle that about drove me crazy. Turned out to be the draw bar vibrating when nothing is...