Search results

You live where it gets quite warm so you might want to try a 15-40. Make sure it is diesel rated (CH, CJ etc.)

It is not abnormal to emit some vapor out the breather. You say your burns 1 qrt/50 hrs, that is getting up there for an engine of that size. It is probably safe to say you have some ring wear. If it runs great and there are no other issues I would run it and keep track of the oil. The weight of...

A bad injector sounds like the culprit to me. It can cause all kinds of damage including scored cylinder, damaged piston,worn rings, diluted oil and smokey exhaust. Bad deal all around if not caught right of the bat. Dirty, contaminated fuel most likely to blame but sometimes injectors just fail.

In the world of hydraulics damage starts to occur over 180*F and increase as the temp rises. To melt the plastic plug you were close to if not more than double that. The fact that the plug melted indicates thats the temp of the whole hydraulic system, differential included was that hot. You are...

That was some serious heat. I think you can be assured that you did damage. At this point you have nothing to lose by draining the oil, refilling and running it and see what shows up first. Seals don't like heat so keep track of hydraulic oil in the engine, external leaks etc.

It is good to replace it. Once the torque tube has been twisted it twist easier the next time. To really do a proper repair it needs to be cut off and re welded.

My bet is the rod that joins the 2 sides of your qa was welded on wrong. One thing to try is to disconnect the 2 tilt cylinders at the qa and then cycle them out and in to see if they will match up. If they don't then you have a bent cylinder rod. Otherwise it has to be the joining rod on the qa.

A 10 year old filter will have nothing to do with it. You need to be more specific as to how much vapor is coming out the breather. It is not unusual for new oil to have more vapor for the first few hours. Can you post a picture?

How are the glow plugs activated? Are they automatic or manual? I had a similar problem with a small diesel that was weak on compression. It would start very well when cold but when it was luke warm, too warm for the glow plugs to come on but with the low compression not warm enough to fire up.

Best fix that intake ASAP. It takes very few hours to dust an engine.:eek:

Im just shooting in the dark here but once you disconnect shaft from engine and take retaining bolts out of u-joint at the transmission end can you not drop the engine end of shaft down enough to pull shaft off tranny splines? I'm just looking at parts manual.

I believe the reason is, the rear support is not sealed so excess grease can escape where the front support is sealed and over greasing could either rupture the oring seal or pop out the sealing cap.

I take from your post that all was fine and it just stopped while operating, is this correct? And when you crank it blows smoke but will not fire? Did you try restarting immediately after it stalled? If the answer is yes to these questions then it sounds like a failure in the engine. If you are...

I have never had any problems from reputable sites. As for spam, I get so much anyway its hard to tell where it all comes from.

Am I correct that you got 3 injectors for $130? If that is the case then you got 3 for the price of 1. Either way you need to have them tested to know what you have. JMHO

A good diesel shop will be able to check your new injectors and tell you if they are correct for your engine.

They can still be the wrong injector. I believe the number you refer to is just a body number.

Injectors are a precise unit and my bet is you have the wrong injectors. Best bet is either take your old ones and have them rebuilt or take your new ones to a shop and have them set to your engine.

Eliminate the simple things first. Indeed if the o-ring is missing or any kind of air leak will give you the symptoms you describe. You may well have had a plugged filter but now you have a different problem.

There is one drain for the engine on the 2620 and 3 on the tranny. And I too would drain the fluids.