Recent content by War Eagle

Assuming you have some kind of smoker then you understand that you must burn the appropriate kind of wood to generate smoke. The process of burning wood to create smokes generates heat and the heat cooks your meat while adding smoke. Cold smoking is made burning the wood outside of your main...

Here is a technique that we have used many times. Do the salt brine but use only half the salt. Brine is for 24 hrs. Rinse very well to remove any surface salt. Cut into 3/4 inch chops. Cold smoke for several hours then vacuum pack and put in freezer. When you want a chop defrost and cook on...

I have a used v1503 te with only 138 hrs. It is off a military generator. The generator failed and the engine was sold separately. I purchased it for a project several years ago but declining health has changed my plans and direction. I would be interested in selling the engine. It is...

Ford: Found on Resevation Dead. Dodge: Damn Old Dirty Gas Eater. Drips Oil Drops Grease Everywhere. Honda: Hang On Not Done Accelerating. Toyota: The One You Ought To Abandon.

I have the 60inch King Kutter II as well. I also have had it about 5 years. My unit is reverse rotation and it can litterly turn my soil into a flour consistency after tilling. I really like this tiller. I put about 20 hrs use per year and have never had one ounce of problems with the unit...

I don't know what tires you have compared to mine but let me tell you how I put anitfreez in my tractor rear wheels. I used 100% windshield washer fluid rated for -20 for my tire ballast in my B3000. No mixture of water. I have the industrial tire not the Ag tire. I put a tube in each of my...

I bought the ATI adapter that would directly connect to the existing Kubota attachment ears on the loader arms. No cutting and re welding. I was afraid of alignment issues when trying to do the re welding. I then cut of off the ears on the bucket and welded a Quick attach mounting plate to...

Thank you all for your input. It gives me enough confidence to move forward with my project.

I am looking for knowledgeable input on how to this might be done. Can I just replace the existing fuel cap with a cap that is made to add an extended run fuel capacity? Most of the ones I have found are for gasoline systems so I don't know if this type of cap would work for a diesel. I am...

I bought a 44.2hp Kubota V1505 TE turbo charged engine with 138 hours on it. It was connected to a military generator and the generator went south. I was going to put it into my tractor that already has a non turbo V1505 but my health has taken a turn and now I don't have the energy or the...

I carry a small hand towel on a hook in my cab and when I first start to work and the condensation starts to show up I give it a quick wipe down and usually only have to do that once and then the system is up and running and takes care of the condensation after that.

I also own a King Kutter 5" reverse rotation tiller. Very heavy duty and does a fabulous job breaking up the soil to very fine consistency. If tilling new area I cut all the foilage first then till in one direction then on the next pass till at 90 degrees from the previous pass.

X3 what the above have said. I have this same tractor but with a cab. I have put inner tubes in the rear tires and put -20 degree window washer fluid in my tires. They hold a little over 17 gallons each and that adds about 138 pounds in each tire. I also carry a 6' box blade on the rear...

I have have added rear wheel spacers and and filled my rear tires with fluid and in my opinion this has made a very noticeable difference in my stability on a slope (as well as a reduction in the pucker factor). My unit has a FEL that I keep lowered as this also helps stability when moving on...

TimP I went out and measured my blades and the front one is pretty close to 17 inches and the rear is 12 inches. Both the replacement blades have been working fine and they have been in place for 2+ years now. The replacement blades have the J hook shape and they were not hard to replace. As...