Recent content by LukyNumbrKevin

  1. LukyNumbrKevin

    While moving 3/4" stone with the FEL heard a pop...

    Great advice, thanks for the quick response. Looks like I have to stop off at the Kubota Dealership on my way home. I have the pipe dope on hand in the basement, thanks for mentioning that as I would have used tape as that is what the factory used.
  2. LukyNumbrKevin

    While moving 3/4" stone with the FEL heard a pop...

    ...and now I have small leak coming from one of the female flat-faced couplers on one of the rear hydraulic lines. I have a few questions that a quick search around didn't help answering: Do the female couplers have an o-ring that is easily replacable? If not, I take it that I have to replace...
  3. LukyNumbrKevin

    Tractor is a blessing

    HAH, I have had my BX for almost a year and a half and I couldn't pay my wife to get on the thing. Tried to teach her how to use it multiple times and she always has something better to do!
  4. LukyNumbrKevin

    What did you do to or on your Kubota today?

    Finished up pulling that triple stump out off the hole with my little BX23s. Here is the video if anyone is curious: https://youtu.be/b14db6Q_yE8
  5. LukyNumbrKevin

    BX Oil and HST Filter wrench's

    I have a BX and this is the one I use, works good for me: https://www.homedepot.com/p/Husky-Universal-3-Jaw-Oil-Filter-Wrench-HU3JFW/204762449
  6. LukyNumbrKevin

    What did you do to or on your Kubota today?

    It wont stop raining so all I can do is rip stumps. I'm hoping May is much more dry than April. Video of the Triple stump I just pulled out: https://youtu.be/0EHa0pb5I-g
  7. LukyNumbrKevin

    What did you do to or on your Kubota today?

    Still getting the paths around my property ready for the spring. Ground is nice and soft so now is the time to get them done. Here's the video if you are curious: https://youtu.be/OnU8P5Je4os
  8. LukyNumbrKevin

    BX 23S new operator question on MMM

    I would double check the manual but I run my BX23s at PTO speed with the MMM and I believe that is where the manual says to run it.
  9. LukyNumbrKevin

    BX 23S vs. 2380

    I think he means that the 3 point hitch connector arms to connect your implements to the tractors 3-point hitch. The BX23s does very much have a rear PTO and 3-point function, you just need to buy the arms which I think set me back about $160, but I just included them in the financing when I...
  10. LukyNumbrKevin

    BX 23S vs. 2380

    The biggest reason I went with the 23s over the 2380 was that with the 2380 there is no way to put a back-hoe on it in the future. The sub-frame that comes with the BX23s for the back-hoe is built into chasis so there is no way to retrofit it to a 2380 with out a very expensive labor bill. If...
  11. LukyNumbrKevin

    What did you do to or on your Kubota today?

    Ground is finally thawed so it is time to get some paths put it on the property, I made a video showing the process so far. This is part 1 of 2, more to come soon! Video Link: https://youtu.be/6eNIiPLQk-8
  12. LukyNumbrKevin

    What did you do to or on your Kubota today?

    haha, thanks for the feedback, I will slow down the next one and take more time editing. I cut a path over the weekend and was able to get some decent footage.
  13. LukyNumbrKevin

    What did you do to or on your Kubota today?

    @michigander, you should check if your dealer will finance the back-hoe the same as the tractor. I know Land-pride is doing 0% APR Financing on some matched implements right now. As far as what I got done: some more spring cleaning to prep for the weather and also the path I plan to put in to...
  14. LukyNumbrKevin

    What did you do to or on your Kubota today?

    Ripped out some stumps and took a video of my back-hoe ripper attachment in action, tell me what you guys think! https://youtu.be/AO5BJwgFveE
  15. LukyNumbrKevin

    LA340S Loader Cylinder Grease Zirk Thread Sizing

    Good Morning Everyone, I was wondering if anyone knew where I could find the sizing and thread specifications for the Grease Zirk on the Loader (LA340S) curl cylinder. The zirk threads came cross-threaded from the factory and I want to re-tap the threads but want to make sure I am doing it...