Recent content by lgeist04

I have an MX6000 HSTC with loader 3rd function 3 rear remotes, 3 sets wheel weights, air ride seat, radio, rear wiper and work lights, quick hitch, block heater with about 70 hours on it. I have decided to hit the road full time in an rv and will be selling it along with the attachments I have...

I have a new MX6000 HSTC that is coming up on the 50 hr service. I have a couple of bottles of Shell T6 5W-40 that are unopened from when I did my 50 hour on my MX5400 a couple of years ago. Is that oil still good to use for my new 50 hour service?

Leave the grapple all the way open when you disconnect the hoses. Then connect the hoses together allowing the grapple to close and the fluid in the lines to drain into the grapple cylinders. I have not had issues since I started doing this.

I agree with the others that 2000lb is the MAX that you could unload and I also would not want to do it all the time. I just unloaded a super sack of pig feed that weighed 2117 lbs. It was on a pallet on my flatbed truck. My pallet forks weigh 300 lbs and it would curl the pallet but not pick it...

My tractor just had it's first regen yesterday with 26.1 hours on it. It took about 15 minutes running at pto speed to complete. Had a pretty strong burning smell and really kicked up a lot of dust from the exhaust.

I have had the tractor for a couple of weeks now and I love it. Thank you for the help with the armrest my dealer finally got them for me after I went back and forth with them on whether you could even get them or not.

How do you bypass it? On the L2501 it was a simple lever that you could zip tie down. I don't see anything like that on the MX?

I have had my new MX5400 for about two weeks now and I am loving every minute of it. I have found however that it is harder to see my SSQA then it was on my L2501. I was hoping someone new how to "trick" my seat safety switch so I could stand up when I am hooking up implements for my FEL?

I had an issue with my L2501 similar to this. The problem was the brake return springs had come off underneath the tractor causing the brakes to drag. Check the 2 springs under you tractor that are attached to your brake pedals.

I used an RCF2060 on My 2501 with no issues. I took it through some pretty heavy brush. It is surprising the torque the 2501 has.

I traded in my L2501 and my new MX5400 will be delivered tomorrow. I have a Landpride RCF2060 that I used on my L2501. I know the MX will be wider than the mower and I might upgrade in the near future my question is will my MX be too powerful for the 2060? It does have a slip clutch on the mower.

Thank you. I am looking forward to it. It should be ready in a couple of weeks. The L2501 just didn't have enough lift and weight in its pants to do what I needed. It was a good tractor though. The MX just from the little I drove it still seemed to be very maneuverable which was one of my...

I just traded my L2501 in for a NEW MX5400 ROPS. It has the third function, two remotes, rear wheel weights, rimguard, rear work light kit and I got it with the Landpride SGC1060 grapple. I asked my dealer about getting armrests for the seat and they say they can't get them for the open station...

What size did you get for your L2501 BigG?

I just got the WG24 yesterday and it works great. It has eaten everything I have thrown at it. My L2501 has no problem running it. I have to say that the L2501 just has a good sound to it when running at pto speed. It sounds a lot meatier than a 25 hp tractor. Like most people have said the only...