Recent content by azzip

I have to admit I use any excuse to outfit the garage better. Course my wife does the same for cloths. I should save up for the electrician that I will need to run a better setup out to the garage, someone thought it was a good idea to run a 24x36 garage with about 100' run of 12awg wire...

Thanks - That's what I needed. I went ahead and ordered an Alloy Tap and Die set in both SAE/Metric, I'm not sure if it has what I need, but it has all the rest of the basic tools so I could just add what I need to it. It has a M6x1, so I shall hope =-) Thanks!

Hello all In servicing my mower deck I managed to break a grease zirk. It's a RCK60B-23BX. I was wondering what the zirk thread size is in this. I managed to get the remains of the zirk drilled out, and now need to chase the exposed threads before reinstalling a new zirk - Do I need to get a...

Thanks. I'm running sudt I was a little concerned since it looked almost milky after use, returning to light gold after about 30 minutes. I will make sure that everything works well after I get completely ready for winter (fel, box blade).

Hello all I recently finished my 50 hour maintenance on my machine (only 6hrs late! =-) and I have noticed that after running my tractor for about 10 minutes, when I recheck my hydraulic fluid it appears that there are many air bubbles in it. I went through and checked most of the items I...

Hello all! I am planning a project to add aux lights for the TPH and a forward looking light to help in the winter with loader use (since the loader will often block the lights). Anyway the plan so far: As far as mounting. I will find a 1" or 1.5" tube or U channel, fabricate a couple of...

Thanks, that's kind of what I thought, just wanted confirmation. I think I will draw a little bit of the fluid off, so that even warm I'm within operating range. Other than that I will consider the job done once I finish up with greasing the machine. Thanks!

It does go down a quarter of an inch when cold. I am also wondering, exactly how bad are the bubbles that indicates an air leak? I can only peer down the check and fill hole, and I will occasionally see some bubbles on the top of the fluid. I was noting a lot of small bubbles in the fluid...

Hello all I am doing 50 hour initial maintenance on my BX2360 and have a question. I goofed on the size of the plug for the hydrostat screen and lost just short of 1.5 gallons (opps... had two plugs. One was a tad too big and one was a tad too small). After changing the filter and cleaning...

Just an FYI - I opted for the KK Standard (II). It seems to lift a pretty well, and I hung up in my wet clay (Just HAD to lower it - it is not new now =-). I spun the tires a bit - I think its mostly the water laden soil right now. Overall pleased =-)

OK I'm gonna lean toward the King Kutter standard 48" box blade. http://www.ruralking.com/48-box-blade-4-shanks.html It's 48" and 350 lbs. I would love to move up to the 60", but I may not have quite enough power to drag it through our wonderful cruddy clay soil. Thanks for the help!

I have a BX2360 and was thinking of doing this. I am leaning towards the magnetic mounting of those LED's. I have used mag mounts for several things, antennas on my car and some emergency lighting and I have never had them delaminate. In fact several of them are not glued into mount at all...

Hello all, I am thinking about getting a grader box for my BX2360. I would love to drag a 5ft instead of a 4ft, but I'm not sure if I can get away with that. I am looking at the local Rural King (think TSC) and they carry or can order both the standard 4ft KK and the XB version. The standard...

Hello all, I was wondering how to mount the RCK60-24b to my B2150. I didn't check the compatibility of the two before leaving the dealership and I'm worried that they are not meant to be together. They were separate when I picked up the tractor, and I can not find a way to mount the handle...

Hello all, I am a new owner of a B2150DT. Rather abused exterior, but around 1084hrs on the clock, and runs nice. Got it for about $7.7k (not including tax) with FEL/Mid-mount 60". Hopefully that is a good price - too late I guess anyways. First question - It has a LA350 loader, I know this...