Search results

The fluid does not only spew when the arms are up. It also spews when I park and relieve pressure on attachments, i.e. buck is down and blade is down and engine has just been turned off the fluid still spews for a minute.

The fluid has no air and does not appear to be hot as it does not steam in this cold weather so oozes out of vent and runs down back end. Next when it happens I will feel it for temperature but I'm sure it is not hot

My B7200 seems to have a problem that I need some help identifying. "Betsy", my B7200 Kubota has a FEL and a rear blade on the 3-point hitch. The hydraulic fluid level appears at the correct level on the dipstick under the seat. Also under the seat there is a rubber plug with in groove in it...

Recently I removed and cleaned the fuel injectors on My B7200 because the engine sounded like it was missing and seemed to lack power. After replacing the fuel injectors and reassembling all the fuel lines I knew I had the bleed the lines. I watched Vic's You Tube Video on this and it seemed...

Steering left and right my front axle moves forward and back on either side sort of cat walking. I believe it is the Center Pin that is the issue. Does anyone know about replacing the center pin bushings and are they pressed in, that is, do you need a hydraulic press the get them out and back...

My 1986 B7200 HST Has been working great until suddenly it stopped moving. The forward / reverse pedal would not make it move in either direction. I have checked the linkages and they seem to be where they should be. Gaining access to the area where the speed control mechanism enters the...

You are quite right. The first hydraulic oil change I used NPAP fluid. For this last oil change I used "RP oil API GL-4 from CRS Petroleum. Both I believe to be good quality UDT oil. On advise from a Kubota Technician I have checked the following: 1. Engine oil level is not going - indicating...

I have recently changed the UDT and cleaned the strainers. The UDT has been sitting for about 6 months unopened and should not be contaminated and is, I believe good quality from NAPA. Once I changed the fluid I thought the problem was fixed but after running the tractor the second time it...

Just a note about the gouge in your cylinder. This may have been caused by the bucket stop (small steel block) that is attached to the loader forearm. I had a similar situation but caught if before the damage was done. If the drift pins that hold the bucket to the loader arms are worn they will...

Hi everyone, Haven't been on in a while cause everything has been running fine. However, I seem to be having some Hydraulic Problems with Betsy, my B7200. When I fill the Hydraulic fluid to the dip stick level and run the tractor the fluid starts to spewing out of what I believe to be a breather...

My B7200 seems to be losing hydraulic Fluid. I fill the Hydraulic Fluid to the correct according to the dip stick. Then when I run the engine a lot of fluid flows out from under the chain bracket plate behind the seat. I know that there is a breather back there but why is the hydraulic fluid...

Hi Gang, Haven't been here in awhile but need some advice now. My 1986 B7200HST with a D950 engine blow the water pump a couple of days ago. Got it into my garage and have picked up an after market water pump bought through my Kubota dealer. My question is, Do you have to remove the rad in...

We know that calcium chloride is very corrosive and many people are looking at a more environmently friendly balast. Some will use recycled antifreeze but I have found the Windshield washer fluid is the most environmently friendly solution. It is inexpensive, easy to use and easy on the land and...

Hi All, If anyone's listening out there, I did manged to separate the Bevel Gear Case from the Front Axle Case. The bad seal is in the swivel joint between the two. So the answer to my question is, Yes, you do have to disassemble the entire Bevel Gear Case, after you remove it from the main axle...

The seal collar on my B7200HST 4wd in the front axle lower end is leaking like a sieve and I'm in the process of separating the front axle. The shop manual is helpful to a point but does not describe how to get at the seal collar (#14 - Pg. M.5-4)without disassembling the entire front axle gear...

Dusty, Good luck with your repairs, especially the loader lift cylinder rebuilds. The rebuilds are fairly easy as I just did one but you may want to watch the price of the rebuild kits. Kubota wanted $180 each for mine on a B7200 and a B1640 loader. That's big bucks if your doing all four...

When I changed the fuel filter on my B7200 I found a needle valve on the injector pump. The B1700 I believe is very similar so you may want to check that out for cleaning. The needle valve is located on the end of the fuel line coming from the fuel pump and has a thumb screw on the top, parts...

:)Hi Guys, Yes, I reintsalled the bucket cylinder and used yellow teflon tape on the hose threads. Started the engine and presto everything worked like clockwork. Amazing! :rolleyes: Now to rejig the actuator. The linkages are sloppy to say the least. I believe the actuator body and pistions are...

thanks very much guys, I will let you now later today how it goes. Have a great day;)

I had a similar problem and I read and re-read the manual on how the bleed the fuel system after a fuel filter change. The book only goes as far as the Fuel injector pump and seems to forget that the fuel injectors and delivery lines are above the pump. By loosening each inject nut on the top of...