Loader hard to get up

Boss Hog

New member

Equipment
B7610 + other MF tractors.
Apr 20, 2022
16
1
3
Illinois
Yes, I know the title of the thread sounds provocative. I really don't mean that. It's just what came to mind.

B7610 tractor with a Kubota loader. When I pull back on the lever it does nothing. When I push forward the bucket goes down as I would expect it to. Both the down pressure and the float position work.

The dump and retract work the bucket like I would expect when I move the lever left and right.

I'm not a Kubota guy, so this is a new issue for me. Wondered if any of you could point me towards where to look to find the problem.

I can get pictures if that would help.
 
Last edited by a moderator:

D2Cat

Well-known member
Lifetime Member

Equipment
L305DT, B7100HST, TG1860, TG1860D, L4240
Mar 27, 2014
15,030
7,744
113
40 miles south of Kansas City
First thing I would do is confirm the quick connects are seated. Remove them one at a time and reconnect them.
 
  • Like
Reactions: 1 user

TheOldHokie

Well-known member
Lifetime Member

Equipment
L3901/LA525, G2160/RCK60, G2460/RCK60
Apr 6, 2021
13,238
7,467
113
Myersville, MD
windyridgefarm.us
Yes, I know the title of the thread sounds provocative. I really don't mean that. It's just what came to mind.

B7610 tractor with a Kubota loader. When I pull back on the lever it does nothing. When I push forward the bucket goes down as I would expect it to. Both the down pressure and the float position work.

The dump and retract work the bucket like I would expect when I move the lever left and right.

I'm not a Kubota guy, so this is a new issue for me. Wondered if any of you could point me towards where to look to find the problem.

I can get pictures if that would help.
What model loader? Does your 3pt lift work?

Dan
 

Boss Hog

New member

Equipment
B7610 + other MF tractors.
Apr 20, 2022
16
1
3
Illinois
D2Cat - The hydraulic couplers were all seated correctly.


TheOldHokie - The loader is a Kubota LA352. All hydraulic functions work normally except lifting the loader up.
020261107_1314430.jpg
 

mikester

Well-known member

Equipment
M59 TLB
Oct 21, 2017
4,179
2,871
113
Canada
www.divergentstuff.ca
Also check your linkages for the joystick hydraulic valve control. If one of them gets loose you will experience problems as described
 
  • Like
Reactions: 1 user

Boss Hog

New member

Equipment
B7610 + other MF tractors.
Apr 20, 2022
16
1
3
Illinois
Just to be clear - the 3pt still works and will lift a heavy implement?
The 3 point works. I do not have anything attached to it at the moment.

I'm wondering if the problem is in the linkage. How do you get this cover off to have a look?

0  lever.jpg
 

TheOldHokie

Well-known member
Lifetime Member

Equipment
L3901/LA525, G2160/RCK60, G2460/RCK60
Apr 6, 2021
13,238
7,467
113
Myersville, MD
windyridgefarm.us
The 3 point works. I do not have anything attached to it at the moment.

I'm wondering if the problem is in the linkage. How do you get this cover off to have a look?

View attachment 181613
The problem could well be the linkage - I have personally experienced that. In my case it was obvious from the floppy feel in the joystick. The plastic cover is typically held on by a 3-4 hex bolts on the underside of qthe base. The most common failure is the helm joint and/or the joystick pivot pin.

Dan
 
  • Like
Reactions: 1 user

North Idaho Wolfman

Moderator
Staff member
Lifetime Member

Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
Jun 9, 2013
36,778
11,486
113
Sandpoint, ID
Should be two bolts (yellow)
You might have to pull the lock knob off (green)

1794205332312.png
 

Boss Hog

New member

Equipment
B7610 + other MF tractors.
Apr 20, 2022
16
1
3
Illinois
I've been busy, so it took a bit to get back to it.
I got the cover pulled back.

Kubota valve (2).JPG


While it was off I played with the control lever. The "down" position works as it should.
Kubota valve (3)  down.JPG

In the "up" position it moved maybe 1/8" off the neutral position.
Kubota valve (5).JPG

I unhooked the linkage. Then stuck the end of a pair of needle nosed pliers in the hole. I put a prybar against the pliers and tried to pry the valve out. That didn't make any difference.

Kubota valve (6).JPG


So I'm thinking the problem is in the hydraulic valve itself. Anyone ever take one apart?

While looking at the hydraulic valve I noticed these things stick out the bottom. Anyone know what they do?
Kubota valve 9.JPG
 

TheOldHokie

Well-known member
Lifetime Member

Equipment
L3901/LA525, G2160/RCK60, G2460/RCK60
Apr 6, 2021
13,238
7,467
113
Myersville, MD
windyridgefarm.us
I've been busy, so it took a bit to get back to it.
I got the cover pulled back.

View attachment 181737


While it was off I played with the control lever. The "down" position works as it should.
View attachment 181738

In the "up" position it moved maybe 1/8" off the neutral position.
View attachment 181739

I unhooked the linkage. Then stuck the end of a pair of needle nosed pliers in the hole. I put a prybar against the pliers and tried to pry the valve out. That didn't make any difference.

View attachment 181740


So I'm thinking the problem is in the hydraulic valve itself. Anyone ever take one apart?

While looking at the hydraulic valve I noticed these things stick out the bottom. Anyone know what they do?
View attachment 181741 p
You are about to dive off the deep end and based on those questions I dont think you can swim. ;)

The things sticking out the bottom are end covers on the spools and inside those covers are the springs that center the spool and ball bearing detents that hold the valve in float. Sounds like the return/detent mechanism on the boom spool is partially jammed. To service that you need to remove the cover on just the boom spool and have a look. Before diving in I suggest you read the WSM and familiarize yourself with whats inside. Lots of little parts that like to run away and hide in the weeds.

Dan
 
Last edited:
  • Like
Reactions: 1 users

GeoHorn

Well-known member
Lifetime Member

Equipment
M4700DT, LA1002FEL, Ferguson5-8B Compactor-Roller, 10KDumpTrailer, RTV-X900
May 18, 2018
6,980
4,309
113
Texas
I see three solutions to your problem: A, B, and C. :

IMG_0396.png IMG_0396.png
 
  • Like
Reactions: 1 user