b2710 HST problem

Bill129

New member

Equipment
B2710
Nov 8, 2026
5
0
1
Iowa
I changed lubricant to be ready for the winter plowing. Drained hydraulic, cleaned the screen (not much in it), changed both filters. Verified level after refilling and letting run/drive for several minutes. Used it to move some dirt and compost. After using for 30-40 minutes, I have no 'gears' to drive. I can use the loader and the 3 point, I can hear the pump whine when I select H/M/L and push down the pedal, but no movement. Before I trailer it to a repair shop, what else can I troubleshoot? Or is the hydro transmission shot?
 

North Idaho Wolfman

Moderator
Staff member
Lifetime Member

Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
Jun 9, 2013
36,778
11,486
113
Sandpoint, ID
Have you checked the range lever?

And Hydrostatic transmissions don't normally just go belly up, especially kubota HST's.
 

JailBreak Your Tractor

Member
Vendor Member

Equipment
BX25D
Nov 26, 2024
37
29
18
Ozarks
Since it started right after the fluid and filter service, I'd go back to that first. Make sure the filter is the correct HST/hydraulic filter and seated properly, the suction screen is clean, and the level is right with the tractor level. A filter that collapses or a weak charge pressure often shows up only once the fluid is hot, which matches your 30–40 minutes. Checking charge pressure hot against the manual spec will tell you a lot before you haul it in.

Jailbreak Your Tractor
 

Bill129

New member

Equipment
B2710
Nov 8, 2026
5
0
1
Iowa
Since it started right after the fluid and filter service, I'd go back to that first. Make sure the filter is the correct HST/hydraulic filter and seated properly, the suction screen is clean, and the level is right with the tractor level. A filter that collapses or a weak charge pressure often shows up only once the fluid is hot, which matches your 30–40 minutes. Checking charge pressure hot against the manual spec will tell you a lot before you haul it in.

Jailbreak Your Tractor
(y)
 

Henro

Well-known member

Equipment
B2910, BX2200, KX41-2V mini Ex.
May 24, 2019
6,124
3,421
113
North of Pittsburgh PA
Is there any chance you might have not noticed a thin clear plastic covering on the end of the hydraulic suction filter? Or that you might have reversed the filters? I think my B2910 has 2 filters (but I also know not to trust my memory).
 
Last edited:

Bill129

New member

Equipment
B2710
Nov 8, 2026
5
0
1
Iowa
Is there any chance you could have not noticed a clear plastic cover on the end of the hydraulic suction filter? Or that you might have reversed the filters? I think my B2910 has 2 filters (but I also know not to trust my memory).
Yep, always a chance, but I know I took it off and I have removed the filter a second time to access the screen and check it a second time as well. The filters are different and I verified they are correct. I bought another new filter for the suction side and will try that by the weekend. Other tasks are now a priority.

Is a bad clutch a possibility of why no movement?
 

North Idaho Wolfman

Moderator
Staff member
Lifetime Member

Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
Jun 9, 2013
36,778
11,486
113
Sandpoint, ID
Yes it could be a clutch issue or a Propeller shaft issue, which is sort of common issue with that design.

2 simple tests can help nail it down.
First engage the pto and see if it spins, then try and move the tractor and see if it still spins.
Put a mirror under the tractor so you can see the propeller shaft.
Start it up, is the propeller shaft spinning?
Try and move the tractor is the shaft still spinning?

1794360219726.png