Search results

Thanks one and all for the input. Thus far I have the OEM blades and kit which has the blade bolt, blade spacer, flat washer and nut hex top lock on order. Probably an overkill in parts but it doesn't hurt to have a few extra OEM's parts on hand. I'll keep the old blades and sharpen them for...

Time for new blades. I've seen a lot of threads and local talk to just get under with an angle grinder and sharpen. I also seen a lot of information on why not to get under and sharpen the blades. For Safety reasons. I follow the reason for safety and I will take it to someone the has a...

Thanks Tooljunkie. Found out I didn't have enough muscle in myself and proper tools to break the lugs for the first time. So ended calling the local field service and they tried two times to save the tire but it failed. I ordered two new ones and will look for a rim and have a spare to work...

First flat in 600 hours on the front. Where is a good point to place a jack stand under the front axle while I run the tire and rim to town for a fix?

Thanks Tool Junkie I going to take the front gangs off and take it to welding shop and let them use the blue flame wrench on the axle nuts and see what falls out after that.

This disc harrow has p/n numbers on it: HA 1009 located on the bearing housing H 975 on the axle housing H 6909 on the axle outside coupling. Please look at the photo and the left front gang has failed and pulled some of the supporting structure out of line. If anyone can tell me a place...

I'm looking at a 12 volt DC sprayer either three point or trailer pull. Where would be a good place on a L 5240 with cab to get 12 volts DC at the rear of the Tractor? I would like to find leads that have an inline switch. I do have some leads hanging where a rear windshield wiper could be...

Did you do the two sets to get 210 lbs per side a total of 420 lbs? I've been looking into rim guard which requires 55 gallons per tire would give more than 1,000 lbs. Do I really need that much weight for GL 5240 LA 845? Grapples weigh 500 lbs and box blade with rippers weighs 150 lbs...

Thanks Tooljunkie. I going to take the FEL off today and look for that sending unit and other PM's. In order to get a reset, once grounded, you turn the key on to make the circuit? Is that correct. Thanks tarnstrong and spreuss. Ditto on the losing prime. Losing prime on my IH364 just...

I have a L5240HSTC-3 400 hours and I recently ran out of fuel even though the fuel indicator showed two hash marks up from empty. Wasn't really a problem bleeding the fuel system and getting it started. But, I would like to know if anyone has experienced this problem and could give me some advice?

Thanks 85Hokie and trouble11 for the input.

My floor is 4" 3,000 psi concrete wire. I'm thinking about adding the 4 wheel weights and was wondering if I would be approaching having to much weight in my enclosed shop floor for parking and servicing the Kubota? the floor is 30'X40' I would appreciate any thoughts about this or experience...

I guess the only option is a rear wiper. Don't how much use I would get out of that.

No do not have a rear wiper. I think there are two sets of wires with connectors hanging down in the cab. Bought the tractor new a couple of years ago. Had the third function valve installed at the dealer for grapple work. There are 4 plugged holes near each other over the drivers right shoulder.

I have plugged holes in the window of the cab. I also have several wires with connectors hanging down. I would like to know what the possibilities are out there to make use of these connections. I guess the plugged holes may be a mounting area for a light to light the rear of the tractor for...

Thanks for the reply. The install sleeve that goes over the radio is a good quarter inch larger in width. The height is ok. It's very soft and bends easy. It has tabs to bend over the existing factory radio frame once inside and then the is supposed radio slips in tight. I've been looking...

I have a JVC X250BT I 'm trying to install using the install sleeve that came with the radio but the sleeve is to large to slide in the radio compartment on my GL 5240. Any suggestions on how the radio will fasten in the radio compartment?

Heavy Duty root grapples made by grace manufacturing. Asking $2600. Includes flat faced couplers for skid steer application. Picture attached. Located in central Oklahoma

Went back to the dealer and explained the difference in size. Actually the service manager came to my assisance. After searching he found the HHTAO-37710 with the magnet. Both filters are labled suction oil filter.

Thanks all. That was some great input. Guess I'm getting spoiled with having a tractor with a cab and thinking every farm chore can be accomplished by the push of a button on the 3rd function valve. After reading other posts on OTT it makes sense not to run up hours on the 5240 for the task...