Search results

  1. C

    B2150 FEL and Three Point issue

    will do and thanks
  2. C

    B2150 FEL and Three Point issue

    after lowering the three point rake over a deep bank, it stopped working UNLESS I adjust the directional valve by the hydrostat pedal. Then the FEL stops working. Either one will work if the valve it adjusted to its function. You can hear it bogg the engine when I select it to the FEL. Any idea...
  3. C

    b7800 tire spin hi range

    they are about the same speed. I have a woods 7200 mower that I swapped between the two tractors. High range on the 7800 is disappointing . When putting it up after use there is a 3 inch ledge of concrete entering my storage shed and the 7800 will not pull over it in hi range. The 2150 will hop...
  4. C

    b7800 tire spin hi range

    Compared to my old 3000hr b2150, I have noticed that on the same incline (hill I mow weekly) the b2150 will spin one rear wheel all the way up the hill (not locking diff in rear 2wd) while the b7800 490 hours will stall until I put it in midrange and then it will spin the rear wheel like the...
  5. C

    B7800 ROPS question

    New to me b7800 hst. I let the rops down and noticed that they are not tight in the down position. THey have about 2 inchs of play and rattle. Is this normal? thanks
  6. C

    B2150 model change

    ;) ANYONE KNOW WHAT MODEL REPLACED THE B2150 HST? anyone KNOW OF A MODEL THAT IS A GOOD AS THE B2150?
  7. C

    Need advice on newer tractor

    Hi, I have had a b2150 for the last 5 years. It is the hst 4x4 with bi speed turn. I have 2700 hours on it now and can't believe how good it has been inspite of the abuse I put it through. I now use it for mowing 4 acres weekly. I pull a woods RD7200 finish mower with it and it does a remarkable...
  8. C

    B1550 power steering help

    my b2150 did this and it was a $3.00 seal at the bottom of the shaft; didn't have to tare dwon the whole unit. took about an hour.
  9. C

    B2150 hst pto stopped working??

    Got lucky, it was the tension pin that couples the hst inputshaft to the clutch. Still hearing the throwout bearing when the clutch is pushed in. Wonder how long it will last?? thanks
  10. C

    B2150 hst pto stopped working??

    B2150 with 2700 hrs while mowing stopped pulling in both directions and the PTO won't turn, Motor runs fine. I had to pull it back to the shop. no leaks anywhere, noticed the clutch was noise when I pushed it in for a year of so now. when idleing now it sound like the clutch rattle that I had...
  11. C

    Woods 7.5 ft Backhoe

    How much? Pins and bushings tight? leaks? thanks
  12. C

    WTB: Mower deck PTO shaft

    Did you have any luck? I need one for a T1600.
  13. C

    T1600 rc44 deck drive shaft needed

    I need the pto or mower drive shaft for a T1600 mower. Any ideas?:)
  14. C

    B2150 industrial tires?

    Hi, I have turf tire on my 2150 and want some industrial tires for the rear. I can't find any in west ky? Any ideas???
  15. C

    B2150 running hot??

    Wish it were that senario. I had the radiator cleaned and flushed at a radiator shop. Is the mower too big at 6ft?
  16. C

    B2150 running hot??

    Do they make the fan that directs air the opposite way?
  17. C

    B2150 running hot??

    Hi, I am a nubie and would like some info from you experts if you don't mind. My B2150 with 2500 hours likes to run hot in the last 1/8" of the temp gauge when I mow. I run it about 16-1800rpms and use a woods 6ft finish mower. I had the radiator flushed and they said it was not bad. Tractor...
Top Bottom