Search results

I was lucky enough to find a "new old stock" loader for my L3750. The loader is a Woods LC108. Unfortunately I don't have the bucket. I do however have a new Kubota brand bucket. I can fabricate brackets to make it fit the LC108 but have no pattern for the pin placement. The width obviously is...

Comparing ratios of optional tires to OEM size is OK but there is still no reference to the tractor ratio. I just want that magic tractor gear ratio so I can effectively plot the percentage of over-run/under-run of the front tires.

Rolling circumference has been pretty well established. The front/rear gear ratio of an L3750 is the only part I am missing.

How did you figure that? Do you have the gear ratio for the tractor? I havn't found it in the WSM.

North Idaho Wolfman, Boy do I feel stupid! I just noticed your attachment. You have provided me with exactly what I need. Thanks much. Evidently the Titan representative I spoke with did not understand my issue or he was a little incompetent. My tractor wheels/tires sizes will stay...

I would be thrilled if the 13.6 x 28 and the 14.9 x 24 shared the same RC. It would save me lots of work, money, and retain my peace of mind. My source was a phone conversation with an engineer/consultant at Titan Tire. He said RC of 13.6 x 28 is 158" and 14.9 x 24 is 150". What is your...

Except that mine has 9.5 x 16 fronts. The combination on your tractor is listed as an option for a 3350 in the WSM. My combination doesn't match to anything. I'm pretty sure that I need to up the rears or lower the fronts. The WSM pairs 13.6 x 28 with 9.5 x 16 as std. on a 3750DT and 12.4 x 28...

Still researching. Kubota dealer got back to me. He says the Kubota branded Workshop Manual is usually the last word. The 14.9 x 24 and 9.5 x 16 set is listed as an option for the 3350 but NOT for the 3750. Workshop manual shows the front axle to be a direct gear drive. 3750 and 4150 use...

Thanks for the reply. I really do appreciate your input. Could I inquire your source? I have the original operator's manual that came with the tractor and also a Kubota workshop manual (from the dealer). Both show only 13.6 x 28 rears for the 3750 DT. A neighbor bought the tractor new and it...

Just acquired a 1985 L3750 4wd w/hydraulic shuttle clutch. The tractor is a one owner (neighbor) that I have known since new. It is "barn fresh" with only 477 hours. A really sweet tractor except the rims are rusted from slow calcium chloride leaks. All info I can find for this tractor shows...

I have a bx2200 and my father has a b2400. I would never trade him. We have extremely hilly ground and my bx comfortably mows where the b can never go. I have a belly mower, a 42" rear brush cutter, and a front snow plow. The size and maneuverability make it great for plowing snow! The only...

Your dealer may be buying small quantities. Mine keeps SUDT in bulk. Last week it was less than $80-. Tractor Supply oil that was claimed to match UDT caused problems this winter. It's too heavy for cold climate. The suction screen in our B2400 is very fine. SUDT cleared it up. SCOTT

I live in Appalachia, a world of hillside farms. My father has retired and no longer runs cattle. Once or twice a year we run a brush cutter over the now unused pasture ground. He bought a B2400 4WD for the task but it isn't working out. It is light, with a high center of gravity and very...

My experience has been limited to simple valves such as used on wood splitters but I am wondering if this is a good time to learn about "power beyond" valves?

I am working on a B2400. The pressure line from the pump to the lift developed a crack just under the seat. While I have this line off I would like to use the opportunity to plumb in an aux valve per Vic's video. I am a little concerned about what kind of control valve I can use. If the relief...