Search results

I don't know about the 4590 but on the 4690 it used a Eaton gear pump. I don't know the model or all the details but the pump was rated at a high rpm (3,000+) with a high displacement (15GPM+). At the 540RPM of the PTO it equated to 4-6 GPM I believe.

This is where I added oil pressure and water temperature to my B9200.

I haven't seen Kubota publish any drawings like that. I've had to reverse engineer a B26 bracket before. Your best bet might be to look at aftermarket bucket manufactures; I have see some of them list the ear dimensions.

My BF350 has the same type of gland. The above is correct, you have to push the gland inwards, remove the cir-clip and then pull the rod out. Mine took a lot of force to get the glands to move inward; when I used a punch I broke/ chipped the gland where the wiper seal goes. I modified a thick...

I had a similar issue with my B9200 and determined that one of the current rear rims would work (Don't remember which); the only difference was 16mm vs 17mm bolt holes. Since I needed tires also, I ordered a tire package through sales instead of parts and was cheaper then the cost for the rims...

The WSM for the B9200HST, which is very similar but older, says the force should be less than 1.3lbs: This is what the troubleshooting section says:

It is from the Kubota BX Price List. If you google Kubota BX price list PDF you can find it. They have different lists for the different series (BX, B, L, TLB, etc). You usually can't find the current year but past years can be found. I use it for finding the kit numbers for options that can be...

Looks like everyone above was correct. Here are the descriptions from the 2022 BX price list

I had fitment issues with their quick coupler; they sent me 4 or 5 different ones and none work. In the end they did refund me and send a return label the return.

This is the section for adjusting the play on a B9200 HST but I think the process is similar on the B8200: I adjusted mine until it was fully maxed out and I still had about 2-3" of play. I dissembled the column and this connection was very loose and worn-out. I reworked it and shimmed...

This post shows the process for removing loader. I put a wood block or brick under each foot so it doesn't sync into the dirt over the winter.

Thanks, that has been my plan but haven't gotten to it. I usually have my backhoe on and forget about the lever. I put the chipper on a couple weeks ago and it reminded me I need to fix it. When I rebuild it I'll report back.

I couldn't find a place that made ears for the BT820 QA either. I had a local shop make ears for $150/pair and made my own ripper from a BXpanded ripper.

The B8200 has a 3 digit hour meter and it's common for them to wrap over to zero. Also the cable going to the hour meter can snap. It likely has 1050hours or more. A good HST should pull the tractor by itself up an incline in high gear. Based on the issues with the HST happen when the oil...

I sent you an email.

Thanks but I already have a ripper, just looking to modify it to the quick attach. That is what I'm probably going to do but all the shops around me are expensive and have long lead times. Before I go that route that I am checking to see if anyone knows any sources for the ears as I can to...

I'm looking to modify a pin-on ripper for the BL4690b to the quick attach coupler on the BT820. I've looked all over the internet and can't find any for this, except the one's from Kubota (Wholesale Kit #BT1977) which are expensive and need extensive modification to get them to match up to the...

No haven't sold it. It is still available

It is possible to retrofit a new model with some fabrication. I put a B2782 on my B9200 which is a little bigger than your b8200; I too was having a hard time finding an older snowblower. I briefly discuss it here. The only issue I have is the snowblower is angled slightly backward (should be...

I opened up the access panel for the valve block and got the manufacture and part number off of the name plate on it. I reached out to a distributor and work with them for what I wanted. It can be difficult if you get someone in customer service who isn't experienced. There are multiple relief...