Search results

Forgot to mention, also have a 14 ft double axle trailer for sale: https://houston.craigslist.org/tro/d/houston-double-axle-14-ft-trailer/7047717382.html

Tractor spoken for - no longer for sale. Kubota L295DT. 1706 hours, 30 hp, 3 cyl diesel, 4 wd, with FEL - front end loader. Also includes: backhoe, blade & plow. Always stored indoors. Includes headlight asm (not attached). PS asm has slight hyd leakage - also a slight leakage at the FEL...

rentthis: I am trying to avoid marring the cylinders as I am getting the tractor ready for sale. Worst case I know that I have pipe wrenches available if needed. lugbolt: Thank you for the detailed info! Its these little tricks that can save significant time (and parts).

Thank you for the reply. I was expecting the end caps to be really tight. If not so tight, I am wondering if I could stick a couple of short bolts into the pin holes and grab the heads of the bolts with a large pipe wrench - I already have access to a 24 inch pipe wrench on site. I don't...

I am assuming that the endcaps on these cylinders are threaded on Is this correct? If so, how much effort will be required to break the endcap free (guestimate please: 100 ft-lbs, 150 ft-lbs, 200 ft-lbs? or much different? Open to any suggestions and advise on how to dismantle the...

Greetings: The seals are shot on my late father's backhoe and I intend to rebuild the problem cylinders. To do so, I will need a pin spanner to unscrew the cylinder endcaps. I have the metalworking tools to make my own spanner but the backhoe is 1000 miles from my location. So if you...

Thank you for the replies. I am pleased that you think the value of the package is greater than $7K. D2Cat: Is that really a reasonable price for the 2WD tractor you pointed to? I see that it has been on Craigslist for about 4 weeks (then again maybe it sold 3.5 weeks ago and the seller...

All: While down in Houston the past 10 days, I put a few hours of use on the tractor. Now at 1701 hrs, hr meter is still functioning. Engine starts easily (at 50F amb temp), does not smoke at start up and does not smoke when rev'd up or under load. Tractor is missing the grille and a small...

North Idaho Wolfman I did not see your message until after I left Texas. I sorted thru the photos I took while the BH was still attached and only found one image that partially shows the attachment of the BH. I am not following your 4th link and where it mounts. I will say that once I...

It appears that the 2nd lever is the draft control lever. I could not find the raise / lower lever for the 3-pt hitch. I am having difficulties controlling the 3pt hitch implement. When I lift up the 3-pt hitch the implement does not remain static. It either continues to lift up...

Thanks for the link. Definitely not the PTO (speed) or the trans shift levers. The levers I am asking about are the ones that control the lift/lowering of the 3-pt hitch. Located to the right of the operators hip. I looked up the link earlier on my phone and only saw one link, not two side...

Question about a new to me L295DT 3 pt hitch levers. The lever furthest way appears to be the lift / lower lever. Is the lever closest to the operator a fine adjust? I searched the forums and read about float control - no idea if that is what it is. I mounted the Kubota 3 pt back hoe and...

Thanks for the quick reply. There was still a little red paint on the head of the plug. Hydraulic fluid was down by about a gallon.

I was working the tractor a bit this morning, doing a bit of yard work prior to putting it up for sale and after about an hour of use I occasionally heard a whine or whistle when operating the FEL. I am thinking I need to check the fluid level. I found a 2 gal jug of UDT that my father had...

Thank you all for your replies. I actually looked at the shut off lever yesterday, before asking my question, and since it was linked with the hand accelerator lever and foot pedal, I wondered why would Kuboto have a second hand throttle - especially one that was so ackwquard to actuate. I...

L295DT, I am only able to stop the engine using the compression release. How is it supposed to shut off-with the ignition switch? If so, where might I find the fuel shut off (solinoid?)? I'm trying to fix a few minor issues before putting it up for sale.

Thank you all for your responses. Yes the tractor is just northwest of Houston, TX. And yes, Craigslist would be my first go to to list it, but was wondering about other places to list. I intend to do a bit of yard/field work when I get back to Houston after Christmas before listing the...

Greetings all: First post. I am preparing to sell my late father's L295DT on behalf of my mother and I am trying to get a feel for its resale value. I understand that the tractor's value might vary geographically. Tractor is located in suburban Houston area. My plan is to bundle the...