Search results

He quoted me a price of $215 shipped.

Yes, I did see these. Unfortunately they seem to be only for the L and M series kubotas. I have the B series. I did get a hold of Mark Hodge. He said that he will put me on the list but it will be about mid summer before he can get to them. He seems to be pretty popular with people that...

Hello, Update: So I figured out what was causing the clunking sound. My lift arm stabilizers had to much play in them. When I was backing up, when the snowblower would shift to the right it would put the shaft at a odd angle causing it to bind. Once I tightened up the stabilizers so that both...

Hello, I have a HS. I understand what you are saying. I've checked the fluid at idle but the bucket was down and in the float position with the PTO disengaged. I've never had and HST before so I was insure if it was different than any other. But someone posted that you can't check it...

It was bought 3 years ago. I doubt they have records of service.

Hello, Filters are white. It's a 2009 so no warranty.

Hello, I have a B3300SU. I have a 5ft 3 pt snowblower. Sometimes when I have the PTO engaged and I'm sitting still or barely moving I get a clunk/knocking sound, that feels like its right under my seat. It doesn't do this when under a load (full of snow) and it hasn't done it at low RPMs. Does...

That's what I am hoping for. I'll get the shims. And once I get the gauge made I'll test the pressure. And post what I found. Thanks for the response.

Hello, Bought my tractor 2010 B3300SU a few years ago used with 450 hours on it. Like everyone it seems that my FEL is a little underpowered. I have bought the makings for a hydraulic pressure tester and will be testing the system to see if I'm reaching even close to the rated operating...

Hello, Just curious is anyone out there using a decent free drawing software for making printable patterns for parts. I'm trying to design/draw up some parts for a bucket thumb. but MS paint isn't cutting it. it wont blow up the drawing so that it will print out a large part on multiple sheets...

If you enjoy fabricating, time's not really an issue. Depending on where you get your steel from, price could very quite a bit. If you have a plasma cutter you are only paying for electricity and consumables. If its something needed right away it may be worth the $300+ dollars it would cost me...

Hello, Just now getting to reading this post. Wish I had done a search on diy piranha bar sooner. Now I can save my money and get myself a plasma cutter and make one!!!Can you please tell me how wide your bar was (back to leading edge of the teeth? It look like about 4". Is that correct...

Thank you all for responding. I ended up going with this one https://www.amazon.com/gp/product/B072F7NJTZ/ref=ppx_od_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 At the recommendation of my brother. His barn is farther from his house than my barn is. He also hooked a work light up to the other plug...

Where did you get the remote switch from? I would like to install one for mine as well.

Used it the first time this morning. Tractor started right up. No rough idle at start up. Worked great.

Well I finally did it. Its been on my list of things to do to the Bota and I gotter done!!!

Wolfman, Between off and start is the run then glow plug position. I activate the plugs for a few seconds and start the tractor. The switch moves back to run when let go. I just turn the switch clockwise until the glow plug indicator comes back on. After 2-4 seconds the idle evens out Ilet the...

Sorry To hijack the thread but: So I asked this last year when I bought my tractor (2009 B3300SU HST). I live in Michigan it's been 30's and 40's here. Last year it was colder, single digits. I bought my tractor used and when it started getting cold I would hit the glow plugs for 10-15 sec and...

Could be wrong but sounds like he already has one.

A picture of the actuator and shute would be great. Ideas without information are not very helpful to the one asking the questions.