Search results

Anyone ever dealt with a similar problem? I would hate to blindly purchase a new button only to find out that the button is not the problem. Thanks!

Just sent an email to you Ric. Been out of internet range for a couple days. Thanks for the chance.

I posted a while back about this, and never really dug into it, but would like to figure it out now. My L4330's display/travel speed button on the dash is not working. I have tested the button per the WSM, and it seemed to be ok. I have tried using a jumper wire to see if the screen would...

Thank you. I contacted them, and though they have seat/base combos that I believe will work, I only want to replace my base (my seat is in good shape). Anyone else have an idea for a replacement base? Thanks

The seat base for my L4330 needs to be replaced in the near future. Looking online at the direct replacement part, all I can find are parts in the $650 range. I would love to find a compatible part for much cheaper than that. Anyone know where I can find a good, cost effective replacement...

Any insights into this problem? Thanks for any suggestions!

I have a very slow hydraulic/transmission oil leak under my tractor where the front of the mid-case connects to the clutch housing (I think). This leak is usually just a few drops a day. Is this something I can live with as long as I watch my fluid levels? Is this something that can be fixed...

Thanks for the replies! I have searched for my loader manual online, but can not find it other than having to buy it. I need to just go ahead and buy it so I have it. However, in the meantime, I have found other similar models and the lift times seem to be around 5 seconds. Mine takes about...

While operating my FEL on my L4330 last night I felt like it was operating slower than normal. Was wondering about the general amount of time it was supposed to take to fully raise the loader from the ground all the way to the highest position. Thanks for any insight.

Her are a couple of pictures of the broken quick attach. I also included a picture of the unaffected side.

Thank you. I will look after work today, and will also get pictures if I cannot tell. Thanks!

I have a quick attach unit on my La853 loader. One of the two handles that raise and lower the pin to lock the attachment into place is missing the bolt and nuts that hold the spring in place and keep tension on the handle. There is an appx. 1/4" hole that looks like a bolt would go in, but...

Rustyw, what is the process to attach the tubes? In the parts diagram it looks like it just has an o-ring and then a bolt hold it to the transmission case and filter housing. The only tube on my tractor that appears damaged is the one from the teams case to the filter. It's about 12" or 14"...

That's probably my main concern. I think the case is thick enough metal that nothing was damaged, but the inlet pipe was bent and pulled out of the transmission case originally.

I need to do an oil change anyway as this tractor is new to me. That might be a good time to do it.

Thank you. Is it a relatively easy procrss to replace that piece? Looks easy from the diagram but I have thought that before and gotten in over my head quickly.

As I was laying under my L4330 today I noticed that the section of hydraulic inlet pipe that comes out of the transmission case and into the filter was bent pretty bad. Looks like the previous owner hit something and it is almost crimped shut. The hydraulics work fine, and it is not leaking...

I do have a tester, but I need a new fuse for it. I'll get that out and test it. Otherwise, what is the process for jumping the wires? It is a three wire plug. One ground, a red, and blue wire. Sorry for my ignorance. I'll also post a picture of my tester later.

Thanks 200! I will give that a try tonight. I am electrically challenged so those steps were not what came to mind first.

Could be. I did not do much except unplug it, pull it out to check that it worked, and reinstalled it, so maybe a connection was bad as well. I am hoping that was part of the problem with the two buttons, but after messing with the connection, I haven't had any positive results. Thanks!