Search results

They said it's been reground and balanced just need to get oversized bearings. Now I just need to get the money for it lol Sent from my XT1609 using Tapatalk

Well I found a rebuilt crankshaft at ag parts for 375.00 plus shipping still have to wait for it. Sent from my XT1609 using Tapatalk

Thanks Steve, the guy at the shop told me that he doesn't think it's going to be able to be fixed they took to much off it and weaked shaft. Now I have to get a crank. Hope you have a great time with your's mines going to have to wait for now. Thanks again for the help Sent from my XT1609 using...

Don't you just love it when they think you have all the time in the world to get your project done! I bet they'd scream like hell if it's done to them. Send pics when you can, does the crank have a lip where the pilot seal goes? This one is so messed up you can't tell anything. They didn't even...

Mine doesn't have a breather cap either someone used a 1/2" PVC pipe with a cap on it an holes in the side Sent from my XT1609 using Tapatalk

No hurry but haven't pulled the crank yet too many honey do's !!! I can wait. Thanks again, Bruce Sent from my XT1609 using Tapatalk

Thanks , I appreciate it. They drilled it out and screwed it up big time even left the flute patterns in it Sent from my XT1609 using Tapatalk

Here's what someone did to mine. Thanks again Sent from my XT1609 using Tapatalk

Hey guy, can you send me a picture of the pilot hole for the crank? I need one to show the machine shop what it is supposed to be. Mine has been bored out to almost 1 1/2 in. Sent from my XT1609 using Tapatalk

No I haven't had a chance to yet, just wanted to check and see if anyone else had one cheap Sent from my XT1609 using Tapatalk

Do you have any engine parts? I need a crankshaft the engine , someone tried to drill the pilot hole out and screwed it up big time. Sent from my XT1609 using Tapatalk

Anybody have a good used crankshaft for a zl600 cheap .? Someone drilled the pilot bearing hole to over 1 inch an it's off center to boot . check out the picture! Sent from my XT1609 using Tapatalk

Help in need of a good used crank for my b6000 ! Whoever had it before me drilled out the pilot bearing hole to over 1 inch an it's not even centered on the crank ! Sent from my XT1609 using Tapatalk

Thanks guys , I pretty much figured that I would have to do that . Paid $800.00 for the tractor with a fel and a 3ft Gannon have spent at least twice that to get it running again ,a little more won't hurt to much LoL Sent from my XT1609 using Tapatalk

First time posting so here goes, my name is Bruce and I have a b6000 that sat for about 11 years outside uncovered so I had a lot of time to get it running again. The clutch started making noise so tore it apart and found that I have a bad bushing in the crank, problem is Kubota says it doesn't...

I'll get the part numbers for you in the morning if you need them. Let me know if you do. I had to replace the pressure pipe on mine it had a crack right at the end spayed oil everywhere. Sent from my Y538 using Tapatalk

I just replaced all of the seals and o rings on mine. The filter takes 2orings at the trans and 2 at the pump , the pressure side takes 2 copper seals at pump and at the trans .Got my parts at Coleman's for under 10 bucks Sent from my Y538 using Tapatalk

Just fixed mine , try tighten the governor , it has a double nut . I tightened***8203; mine so that it's now got resistance. The trottle now stays where I need it to. The book says that there is a friction plate on the governor for resistance. Bruce Sent from my Y538 using Tapatalk

Mine did the same thing , check the bolt on the bottom of the solenoid to the brushes mine was loose tighten it works just fine now Sent from my Y538 using Tapatalk

Mine broke I just put it in the vise and soldered together works just fine Sent from my Y538 using Tapatalk