Search results

Marshall Machine Co in Everett WA - 4two5-29zero-seven635

I ended up ordering 15" of 1-1/8" Chrome steel Rod from supplier in Texas http://www.alloysandcomponents.com/chromerod.htm Cost about $30.00 shipped.. took it to machine shop in Everett WA (Guy runs out of his back yard) he charged me $100 labor to duplicate the bent rod.. He even assembled it...

I ended up ordering 15" of 1-1/8" Chrome steel Rod from supplier in Texas http://www.alloysandcomponents.com/chromerod.htm Cost about $30.00 shipped.. took it to machine shop in Everett WA (Guy runs out of his back yard) he charged me $100 labor to cut & duplicate the bent rod.. He even...

Form what I understand, the following are options to mount turf tires on my B7100? Are there any other options than what I have listed? kind of on a budget looking for alternatives as this is an older tractor.. Rear Turf tires size I need: 29-12.50-15 Rims rear I need are 29x12.50x15-6 (6...

My B7100 tractor is gear drive, The backhoe has a separate pump and the FEL has a separate pump. Just to be clear, does the tractor have an Internal Hydraulic Pump which runs the the 3 point lifting arms? (If so where is pump located?) Sorry for the dumb questions, this is my first...

Thanks for sharing that, I ended up ordering 15" of 1-1/8" Chrome steel Rod from supplier in Texas http://www.alloysandcomponents.com/chromerod.htm Cost about $30.00 shipped.. took it to machine shop in Everett WA (Guy runs at his house) he charged me $100 labor to duplicate the bent rod.. He...

OK, will try this

I did not mention that my Tractor is gear drive. Does that make any difference on lift ? So I lowered the idle and took the plunge and raised pto lift while engine was running and it worked, but the squealing is worrying... (It sounded like gears but I guess it is whining) Would adjusting...

From what I downloaded part 3 only goes to page 46 ?

Thanks for link! yes this will help.. Do you know if part 4 or 5 is available for service manual B7100 ? Thanks again

thanks for info so far, so the lift is hydraulic? Wow, it sounds so much like gears grinding.. so unless I am missing some procedure to engage the lift (as this is the 1st time I ever used the 3 point lift) or i did something wrong in hooking the mower up, I will check that out.. Could someone...

Sorry wrong terminology.. yes the 3 point is grinding if I try to activate the raise lever while the engine is running. If I turn off engine, engage lever, it raises OK. Definitely sounds loud like gears grinding.. araid to pull lever further as I might chip some teeth or cause damage?

1st time attaching a woods mower on a Late 70s early 80s kubota Gear driven B7100. When I attempt to engage the lever to raise mower attachment while tractor is running it will grind loud. I know the lift works, if I shut OFF the tractor, engage the lever to lift position and restart the...

Thanks, I am aware of that.. it is $300-$400 range for a new rod installed. But my post is to find someone who has utilized an aftermarket one. There are others interested in these as well. Thanks tho..

OP, Any more info on the Maxim Cylinder? Just a follow up on this thread, I am trying to locate an aftermarket cylinder replacement as well. I do not know if I am using correct method to determine Stroke or not, but My B219 FEL cylinder rod length extended is 28-1/4". When closed, it is 17-1/4"...

Thanks, does anyone have specs on that Kubota cylinder? Not sure of bore? I thought it was 2" Bore 1-1/4" rod per another post.. but, my measurements are as follows Barell is 2.380 so is this 1-1/2 or 2" bore? Rod is 1.125 IDK how to measure stroke exactly, but measuring from center of...

Anybody Modify Aftermarket Cylinder for B219 Loader ? I have seen a couple posts about a Maxim Cylinder.. or this Dalton http://www.daltonhydraulic.com/dalton-welded-tube-cylinder-2-bore-x-18-stroke for $160 delivered. but no followup on modifications? It seems the brackets need to be cut down...

Looks to me that the $130 maxim Maxim WT Welded Cylinder: 2 Bore x 18 Stroke - 1.25 Rod Dia. SKU: #288314 Will NOT work as a replacement. unless modified? the pins on the Kubota are 5/8" thick (Approximately?) The pins the 288314 are designed for are 1" The brackets on the Kubota are...

Someone mentioned this on another page here: "the mountings look like they need a 1 7/8" bracket at each end because that's the frame width on the B219 FEL. I saw mention somewhere on this forum of a http://www.ebay.com/itm/MAXIM-288-31...item3396fdfa53 Maxim 288-314 cylinder but the ned...

Hello Turk999, Could you follow up on new maxim cylinder 288-314 ? I am considering a purchase of this cylinder for same loader. The chrome rod has some pitting on mine. Are the Fittings the same? Did it bolt on ok? I have one leak. Would it be OK to have OEM cylinder on one side and the Maxim...