Search results

Thanks Kubotasam! Here is a video of the setup: https://youtu.be/CljnRo8t4Qs Pictures below.

Finally got the snowblower going Finally, everything (well, almost everything) is running on the B6000E :D:D:D. I mounted the snowblower up front. Added an auxiliary hydraulic pump and a 1.5" bore x 6" stroke ram to lift and lower it. The blower runs off the rear PTO similar to the Erskine...

PenderBen, where in BC are you located? I may be interested in your tiller and have some contacts in Kamloops that would be willing to help out if needed.

I have what I think is a factory supplied FEL mount since the holes line up perfectly with holes on the B6000 frame. I think it is for a B-206 if anyone can confirm? I am missing the loader arm assembly and bucket and am looking for one that will fit. The width between the loader frame uprights...

I finally got the new belt on. I'm not sure if the way I did it is how it is supposed to be done, but it worked. I ended up putting a jack under the lip where the engine meets the transmission. Then I removed the hood and all but the 2 rearmost bolts that secure the frame to the engine. After...

Anyone have a user manual? I have a shop repair manual and a parts manual, but I'm sure belt replacement is described in the user manual which, of course, I do not have. I also suspect that when my tractor was new, there was enough clearance. I haven't looked at it too closely, but I'm guessing...

Hydraulic would be my first choice to run a snowblower, since I wouldn't have to mess around with linkage (belts, shafts, or roller chains) when it lifts and lowers. I just assumed the B6000 doesn't have enough horsepower to run a hydraulic pump big enough to power it. Any idea how many GPM I...

I'm sure this is a "well, duh" question for everyone here but me, but how do I replace the fan belt on my B6000E? It looks like there isn't enough clearance between the crankshaft pulley and the frame to get it out. Of course, I could just cut it and slide it off, but that leaves me with...

Darn, if we only had Peavey Mart south of the border. Tim Horton's too.

Guess what I picked up today... Guess what I picked up today...a front-mounted snowblower. It was for a not-so-popular Honda riding mower. Saw it sitting next to a mower/implement dealer. When I asked about it, the guy said he wanted 75 for it. My response was "you mean dollars?" Snatched it up...

Ed, Sorry for the delay in my reply...been busy. The width between the loader uprights is 36 1/4". ......

Re: FOR TRADE/FS B6000 Front End Loader FEL Mount Ed, ...... As for the ROPS, visited Kubota dealer "A" and was told is not available. Called dealer "B" and they said the ROPS program is no longer in effect, but they could get one from a dealer in Georgia for $340 plus shipping (with the...

Re: FOR TRADE/FS B6000 Front End Loader FEL Mount Thanks for the heads up ShaunBlake. I looked into a ROPS from the local Kubota dealer. The parts rep said he didn't think a ROPS was available for my model because of its age and would do some "calling around." I haven't heard back yet, so I'll...

So, the story goes...the guy I bought my B6000E from said he purchased it at an auction with a front end loader. When he showed up the next day to pick up the tractor, someone had stolen the loader itself, leaving the mount on the tractor. The loader mount looks like it is factory made, and the...

I had the same question. Now that it seems to be answered by the last post, I have a couple more about my B6000E: 1) Should the rear wheels be mounted on the outside or the inside of the hubs. When I purchased my tractor, it had one of each (sorry if this sounds like a rookie question :) ) 2)...

Thanks for the advice 85Hokie. I did exactly that. I measured with an OD tape measure and it was awfully close to 1.25". After poking around on K&N's website, I found and ordered one and it was a perfect fit. It is model 62-1390. I think it is for a motorcycle application, but it is now the...

I wouldn't think 25 ft. lbs. would do it, but is there a chance your injectors cracked during torquing? Again, a long shot, but it might be worth a look. Let me know if you are parting out and selling the PTO reverser though. :cool:

Lowered to $1500.

My B6000 is missing the oil bowl. While searching for one, I ran across a B6000 on eBay (where else?) that had a non-original air filter. This could be fabricated, but my guess is it's off of a later model Kubota. Can anyone identify it, or suggest how to fabricate one? It seems like it would...

Hmmm...hadn't considered a friction drive. Yes, I am a little concerned about the lack of horsepower on the B6000 running a snowblower. I may have to stick to something like a 37" blower. I think I remember reading somewhere that only the 540 speed should be used for implements. I'm not sure...