Search results

I have a M105X that has only 2000 hours. I bought it new in 05. The PTO started slipping when I was cutting hay with the disc mower about a week ago. I have a WSM and it says to check the pressure under the PTO solenoid. It is supposed to be between 298-325 psi when PTO is running. I hooked a...

What is the quickest procedure to get hydraulic fluid to operating temp. I cant find nothing on it in my WSM. I have a slipping PTO on my M105X. And i am going to do a pressure test but fluid temp. needs to be correct.

I am in the process of changing out compressor, condensor coil, expansion valve and drier. How much oil do i need in the system after flushing everything out? Will compressor come with oil inside of it?

I am having problems with my tractor. Sometimes it will just start smothering out and finally quit. Then it will not restart untill you loosen banjo bolt at injector pump. Then pump the fuel pump knob located on top of the fuel filter. You have to loosen the banjo bolt because the air will not...

My M105X is leaking hydraulioc fluid out of the shaft of the steering controller. I am gonna pull it myself and take it to my Kubota dealer and let them re seal it. When i pull the shaft and ujoint off of the controller. Do i have to mark anything to make sure it goes back on the same place on...

I have a M8200 4wd with cab and air.I have been lookin for a long while for a used loader to fit it.I just bought one that came off of a M9000.It is a Quicke Q750.Has anybody here got one of these on a 8200 or 9000?If so I would like some help and maybe even some pics.

I have a 4wd C/H/A M8200 that I need to put a loader on.This 2wd 8200 with a Bushog M446 loader is coming up at a auction near my home.I am thinking about trying to buy it and swap loader to my 4wd tractor.I am worried the 2wd brackets wont fit because the Bushog part numbers are...

I have a real good M8200 with the hydraulic shuttle.I have been looking for a used loader for it.When I look at the specs on the M8200 on Tractor Data it says the Pump Flow is 17.1 GPM.The M9000 is rated at 23.1 GPM.Is this correct?Would that mean the loader would be quite a bit slower in...

I have a little 3 cylinder Kubota that should not be this hard to start.I bought it not running and when I got it home and finally got it started.It was blowing oil out of the blowby tube bad.I had a inframe overhaul done on it and it runs pretty good now just really hard to start. All of the 3...

I just bought a L2002.It is going to need piston rings because it is very hard to start and blowing oil out the exhaust and blowby tube.I understand my little Gray L2002 is a lot like a L275.Tractordata shows the L275 has a live PTO and my L2002 does not.Is this correct?What type of fluid goes...

I seen a M110X at a auction and it had a factory buddy seat installed.The 110X is one model newer than my 105X but the cab and the left side where buddy seat is mounted looks exactly like mine.I called my dealer and they do not show a buddy seat for my tractor.They have a complete one for $500...

I have a m105X that has a wait to start light that comes on when it it cold.I don't see any light on my M8200.Does any of the M??00 series tractors have any kinda start assist in cold weather?

I have a good 03 2WD,cab 6800 with 1950 hrs. It has 50% 30" tires on rear and one new and other 60% on front.2 remotes on rear.I have owned it for the last 6 months and there is nothing wrong with it.It has the upgraded A/C system and it has the coldest A/C I have ever seen in a cab tractor.New...

I am looking for a tractor to use on a hay rake and tedder.I probally will not put 75hrs. a year on it.I found a dirt cheap 2WD Cab,heat,air 2007 6040.I do not know the history on it.It is showing 3200 hrs. I have heard it was used as a bushog tractor from the state of Georgia.I know this is a...

I am pretty computer illitarate but i see you can download a Work Shop Manual for a mere $18.99 from tradebit.It says the manual has 960 pages. Messicks has them in shrink wrap from Kubota for $76 part #97897-180004.What would the differences be?

I just bought a 02 M6800 with 1900 hrs.I thought the A/C was really working good and it was as long as temps. were below 80 degrees.When the temp get above 80 it gets kinda uncomfortable in cab.I have put the guages on and the pressures are about right.When i first got it I had to add 134a...

I just bought a 02 M6800 C/H/A 2wd,manual shuttle w/1900 hrs.I am using it in my hay operation.This is the roughest riding little tractor i have ever been on.Could the cab mounts be worn out causing rough ride or do all of them do this?The clutch is pretty hard to push also. Pros:Best A/C...