Search results

Well, Kubota denied the "good will" gesture. The dealer indicated that on a 2nd owner machine, that is typically the case. We bought it off another couple with 100 hours on it. They were older and couldn't deal with the jumpy gas pedal. The dealer is providing us with information/diagnostics and...

Got a call from the service manager today - We pushed back a little with the dealer, and asked if there is anything Kubota can do to assist with the problem, since we're just outside of warranty and this sounds like a major issue. The dealer is also frustrated because it sounds like the tech...

Update - dealer still has the XG850. They had to order all new tools and testing equipment because they did not have the tools to properly test this specific model. We just got a call today for an authorization for work - they want to remove the head to inspect the valves - and mentioned a...

Our XG850 has now been at the local dealer almost a month. They are at a bit of a loss as to what the issue is - They seemed shocked that it has a Subaru engine and that they did not have the diagnostic tools for that specific engine and also tried telling us the ECU is from a 2022 XG850, which...

any updates on your situation?

That doesn't make it right. Both of those tie rods should have been recalled, too if it was inside the service life of the part. And yes... if there is a known mechanical defect the manufacturer is dragging its feet on replacing, repairing, or informing about that becomes a safety concern - then...

how is there not a recall campaign on them if there is a known design flaw. so what do I do? have it fixed and trade it back in? Mine is a 2020 with ~400hrs - it is no longer under warranty. I will have to pay out of pocket for any repairs.

OP here. Sorry for the lack of updates - I have been slammed with work and haven't really had any time to deal with this in the past few months. We're basically just using our quad now and our like new XG-850 just sits parked. I am so upset with this XG850 - we have very low hours on this unit...

no updates yet. coleman's cancelled my order. looks like the ignition coils jumped up in price to $250. yikes. I was going to proactively order a pair. I guess I will just be checking these with my meter. I will replace the spark plugs and start there, since they are past due. Thank you. Will...

Pulled the plugs - they both look fine and are indeed firing. No excessive fouling and they were not wet. Since we're nearing 400 hours, I proactively ordered a replacement set of plugs last week and they should be here this coming week - yikes those are expensive plugs! I also ordered the coil...

this was also a thought of mine. like maybe the emergency brake was partially stuck or something, but that would sound an alarm, wouldnt it?

This is a 2020 RTV-XG850. They are fuel injected. I use it almost daily, and the gas is less than 2 months old. Mostly short trips taking the kids to the bus stop and back. I know our old RZR would foul out if it had frequent short trips, so pulling the plugs is on my list of things for the...

air filter looks brand new. i blew it out with air just to be sure. is there any procedure for checking the ignition coils? I'll pull the plugs this weekend to inspect them. I was also going to pull the fuel filter to check that, too. this thing isn't run very hard. it has had a fairly easy...

I own an RTV-XG850 with ~100 hours on it (400miles). It just started having an issue where if I give it full gas, it will backfire and pop and will only accelerate to ~20-22 MPH. It almost feels like governed like when you hit the top end limit ~40 MPH. It seems to idle perfectly fine and if I...

The harness plug looks to be a 12 pin Deutsch: https://www.ebay.com/itm/264911877483?epid=1241203780 I was actually debating on adding one of the following: A Bluetooth AMP for $65 https://www.amazon.com/Amplified-Wireless-Bluetooth-Audio-Controller/dp/B07YCSPFG6/ref=sr_1_21? Or a Boss Gauge...

I bought a barely used RTV XG850 that has the premium roof installed and the speakers and wiring harness installed (12 pin), but no radio kit was installed. It looks like the Kubota kit (Kubota Part#: 77700-VP0897) uses a Jensen Powersports JHD40BT radio, but I can't find a part number or any...

is there any word or symptoms as to how or why the old unit failed? was it making any noises or issues prior to failure?

For the price when we got our BX1880, nothing else could touch it price-wise. That was with a MMM, the Loader (with ss quicktach bucket), and a Back blade. I have since added a box blade and a bunch of other attachments and managed to snag an older Yanmar 32" 3pt rototiller that works great with...

I own a newer BX1880. This has a larger single cylinder. [update] just as an update. ive put 5-6 more hours on it and haven't had a single issue. i dont know what caused the issue initially, but i cannot get it to repeat the problem. looking at the loader cylinder, there seems to be no issue...

I am aware of this issue and it was not anywhere near fully extended when backdragging. None the less - how do I check / verify a broken cylinder? Wouldn't a broken cylinder either be always broken or not? Not sometimes broken and sometimes not? The quick connect o-rings would likely be a non...