Recent content by slevys95

  1. S

    BX2350 Plastic Panels

    Good info. Curious if anyone has heard of a metal replacement lower bonnet that slides around engine. One side of thumb screws finger is broke and other side is on way out. Bouncing around on my bumpy turf. Thanks for any input.
  2. S

    BX2370 won't restart after shutdown unless battery is jumped

    Thanks guys, after a few days hiatus for birthdays and a wedding, finally got back to work. The folks at my local local Kubota dealer(Bentley Bros in Brockport NY) are gems. Printed out a schematic for me of electric system. Traced all the wires, education in itself, while tracing wires the boot...
  3. S

    BX2370 won't restart after shutdown unless battery is jumped

    I will try this tomorrow. Thanks again.
  4. S

    BX2370 won't restart after shutdown unless battery is jumped

    Thanks guys, Did test battery as suggested. I even bought a new battery. Same scenario.
  5. S

    BX2370 won't restart after shutdown unless battery is jumped

    Question if anybody else has this problem or had it? Hadn't seen this particular problem on any threads unless I missed it. BX2370 won't restart after stopping without jumping battery. Battery is good, checked safeties, limit switches and connections. Battery is just draining while it's running...
  6. S

    ROPs Carry All Basket

    Thanks for response. I like this setup. I was looking into a ammo box on post of ROPS. But since my bx2370 is stored in barn. I could do with the open tray. Much more useful. Sent from my Moto Z (2) using Tapatalk
  7. S

    ROPs Carry All Basket

    Very nice. How is it with ROPS down? I have to put mine down often because of mowing around low tree limbs. Sent from my Moto Z (2) using Tapatalk
  8. S

    ISO a B1640A loader

    I have a B1750 and I am looking for a B1640A loader . From reading others posts it appears a loader from a B1550 would fit. Any suggestions where else to look. I contacted EA but they suggested Woods , which as far as I can tell from website they don't have any either. Thanks in advance for...
  9. S

    Photo shoot anything lately? Random Photo Thread

    Traveling from Western New York to Indiana. Sent from my Moto Z (2) using Tapatalk
  10. S

    Made myself a pallet fork attachment

    Nice work on forks. I'm in the process of fabrication of a set of bucket forks also for my bx2370 with fixed FEL. While at junk yard looking for scrap metal to practice some welding I tripped over an old set of skid steer forks. Asked what yard wanted and he said $10. Needless to say they ended...
  11. S

    Let's see those chainsaw mounts!

    Just finished ballast for my bx2370 looks much like Daveinwestmi. Should have left some room on top to store loose tools like he did but was thinking of it holding water. Chain saw scabard is from old chainsaw that died. All scrap metal except drawbar that was bent. Concrete from big box stores...
  12. S

    2-3 ft of snow to much for blade

    Thanks for response. Makes sense not to overdo front with chains but had icey conditions under snow with little ability to steer. I will try with just rear chains and see how it goes. We've had different types of snow from powder to heavy moist stuff. Also keep in 4 wheel most of the time...
  13. S

    2-3 ft of snow to much for blade

    You guys seem to know your snow moving skills. I'm a newbie with a back blade on my older '80s B1750. 5 foot blade, manual angle setup. Had a few snow storms from about 12 to 4 inches. Driveway is only 250 feet, but thought I did ok plowing in reverse pushing snow to sides of drive. Now the...
  14. S

    B1750DT Split

    Re: 1750B Standard shift split Thanks in advance for any info Sent from my XT1585 using Tapatalk