Search results

I’m trying to determine if the Kabota LA 304 364 and 504 loader arms are the same. They appear to be exactly dimensionally equal and all measurements match. It seems silly that Kubota would build identical arms of different thickness. Can anyone tell me if they are the same arms just labeled...

I have a B 1550 Kabota tractor with approximately 1300 hours on it. I have owned this tractor for almost 2 years and in this time I have replaced the hydraulic pump. I am currently having two of the cylinders rebuilt for the bucket curl and I am putting a new valve for the loader on the tractor...

I have a B1550 gear drive with power steering and a 1640A loader. I have owned this tractor for a few months and have been using it the last week or so to move quite a bit of gravel around my property. I have found by accident today that if I hold pressure on the steering wheel left or right...

I'm looking at picking up a fairly decent Kubota b1550 gear drive tractor. It currently has a set of turf tires on the front and a set of I guess what they call the V bar wide rear tires. I would like to switch it over to the factory AG size tires of 8-16 in the rear and 6-12 in the front. Can...

I am looking to buy the part number listed in my title for my b6100 hydraulic line. It's the diverter block that allows you to tap in to the 3 point hitch Hydraulics to run an attachment. If anyone has one they're willing to part with please let me know. #70070-00385

I read on the internet that the hydraulic pump from a B8200 Kubota would fit on my B6100 Kubota. I believe the Kubota pump for the bB8200 is a 6.5 gallon per minute pump versus the 3.5 gallon per minute pump currently on my 6100. I have located a part number of 67810-76100 for the B8200 pump...

I split my newly purchased b6100 in half to do a clutch. I also purchased a new pilot bearing as I figured it would be good to replace it while I was in there. Unfortunately both of my propeller shaft and the inside of my crankshaft where the pilot bearing goes are completely worn out. It...

I believe the factory flow is 3.1 gallons per minute for the 6100 engine mounted hydraulic pump, but can anyone tell me the operating pressure of the system. Thanks

I recently purchased an excellent condition Kubota B 6100 gear-driven tractor. I would like to put a Front end loader on this tractor and know that my chances of locating a factory b219 loader are slim to none. What brand of loader out there would you guys recommend. I prefer a more traditional...

I am looking for a factory set of Kubota rear wheel weights for a B6000. If anybody has some or knows where there's some available I would be interested thank you

I have been unable to locate any tire chains small enough for the rear tires on my B6000. The tires are 7-16 AG. None of the tire chain places I've been to on line have chains that small. Any recommendations and also like to buy some wheel weights for the same tractor. Thanks

Picked up my rollover protection for my B6000 from the Kubota at the dealership today. Unfortunately I did not look closely at it until I had already stripped down half of my tractor and was getting ready to do the install. When I realized that nothing was going to line up. At that point I...

My recently purchased B6000 Kubota 4x4 tractor has a Kubota B211 front end loader attached. The factory manual I received with the tractor says the rear end should take 80 90 gear oil, however the b211 front end loader also takes its hydraulic fluid from the rear end. I had the valve and a...

I need to replace the drag link on my b6000 Kubota tractor. The bad news is it's a discontinued part and not available anywhere. My plan is to take the drag link I have and have a machine shop add threaded ends so that I can put standard tie rod ends on to it. Does anybody know the dimension of...

I was woundering if anyone could tell me the lift capacity for a B211 FEL mounted on a B6000 tractor. The loader is powered directly off the tractors hydraulic system. Thanks