Recent content by zbhover

I made a some bucket skids like these for the bucket on my B2620, and they work pretty good, see my post at: http://www.orangetractortalks.com/forums/showthread.php?t=18496 Using float they don't sink into the gravel enough to start scooping gravel up, but if your not paying attention and the...

Yesterday I finally got to use my post hole digger for the first time on my B2620. Probably a year and a half ago I picked up an old Shaver post hole digger with a 12" auger for $175, cleaned it up and painted it and built a stand for it. The stand makes it easy to move around and also easy...

I have a B262p and they don't offer a mulch kit for it so I put a set of gator blades on the mmm and built a mulch door for it. Here is a link to that post http://www.orangetractortalks.com/forums/showthread.php?t=16704 It works pretty good, I keep saying I'm going to build a set of deck...

I made a ripper attachment for my rear blade when I wanted to run power out to my shed for my block heater on the B2620. If I remember right I used heavy wall 1-1/4" angle iron for the ripper "tooth" and some pieces of plate I had laying around for the rest. Its just a snug fit over...

Here is one of my toy builds in progress..... Except we bought a repo'd house that we completely gutted and started over so I haven't had time to work on it much in the last 2 years or so...... Its a Convertible 69 VW Bug on a shortened and lowered S10 chassis with a 350 up front...

How about these??? http://www.ebay.com/itm/Set-of-3-new-Gator-mulching-blades-60Pro-mowers-Kubota-ZD323-and-Z725-396810-/261532207333 http://www.ebay.com/itm/OREGON-GATOR-BLADES-396-787-KUBOTA-SET-OF-3-60-DECK-20-6-BLADES-NEW-/262161905385?hash=item3d0a1136e9:g:TsMAAOSw8-tWV0m~

s I had a couple people tell me that the G-6 blades are heavier than the G-3 and stock blades so it could cause excess wear on the clutch when engaging a heavy set of blades. I have no clue if there is any truth to that or not???:confused:

I don't know if it helps you out or not but the G3 Gator blades for my RCK60-29b mid mount mower deck on my B2620 were part # 96-393. They didn't make a huge difference until I made a mulch door for my deck though, which you can see here...

We had several dead bushes in front of our house that I have been avoiding pulling out because I figured it would be a pain in the butt. The B2620 and Piranha tooth bar made easy work out of the job, wish I would have done it earlier.... LOL I was able to get under the roots with the tooth bar...

I just used regular teflon tape, should hold up just fine, teflon is eared at a pretty high temp if I remember correctly.

You can't see the half finished V8 VW beetle behind me and the hovercraft I'm working on that I pulled out :D

I can get it at the Macdonald Shell on Allen road in the north end of peoria or the Macdonald Shell in East Peoria, and there might be a couple others around here too. It looks like this Freedom in Springfield might? Freedom Bachman Dr. (near 3975 N. Dirksen Pky.), Springfield, IL 62702...

Menards had their unfinished oak cabinets on sale again and I had a couple rebate checks so I picked up the last 3 cabinets for the other side of the garage.

I put about 8 hours on the B2620 this last week using my piranha tooth bar to widen our driveway by digging out and re grading the hill on one side and removing a little dirt from the other so It wouldn't be high. Boy did the tooth bar make a worlds of difference!. I then got 15 tons of 3-4"...

Well I decided to go with added weight to my rear blade since it was free to do vs paying to have the tires filled. We had some scrap 5" square tubing at work that I welded end caps on and filled with steel shot. This added 280lbs to the rear blade which is just shy of 240lbs making about...