Recent content by edwardsonmark

  1. E

    Edge Tamers…

    Agree, mount them at about thirds of the bucket. Sent from my moto e5 supra using Tapatalk
  2. E

    Bx Series - Inner tie rod replacement boots

    Well im going to let the dealership replace them once more under warranty....my last service experience with them was terrible so I am going to give them another shot in case I really do need them in the future...given the last set was put on 6 months ago I'm sure I will be looking for...
  3. E

    Bx Series - Inner tie rod replacement boots

    My assumption is it is pretty good likelihood if I have had inners replaced under warranty once already it would be smart to do outers at the same time I pull everything apart to do inners? Sent from my SM-G930V using Tapatalk
  4. E

    bucket vs box blade vs blade

    I would suggest a land plane. I hate my box blade but maybe I can't figure out how to use it correctly the 15 times I have tried it Sent from my SM-G930V using Tapatalk
  5. E

    Flag

    I believe it is for police or fire department support
  6. E

    BX2350. Three point linkage problem

    Can you take a picture of the back of the tractor so we can see how it is set up ?
  7. E

    48" Box Blade Choices

    I don't like the clevis type hitch on my lp. I also really don't like how the shank adjustment on my lp. I have seen fixes for this but your spending additional money to fix the design flaw just my .02
  8. E

    B2673 front Blade

    I am also on a gravel drive Sent from my SM-G930V using Tapatalk
  9. E

    B2673 front Blade

    I started with a 54 in atv blade then welded extensions on each end. I have a bx2670 and the blade is right at 84 in wide. I assume snow is the main use all above are speaking about. I have no issue pushing it and also do not use fel float but there is some float built into my design Sent from...
  10. E

    BX 80 series quick attach loader

    Re: BX 80 series quick attack loader I really like the ssqa....and the manifold and joystick location! How did you get one when they aren't even offered on the kubota website?? I am really thinking about looking at the 23s and trading my 8 month old 2670! Wonder if the ssqa adaptor can be put...
  11. E

    Adjusting the rear track width on a 7510

    Not sure if there's room but I have used a bottle jack inside right above the axle on older tractors. Like I said not sure if that would have worked here or not. Way to use what you have available to you to get the job done! Sent from my SM-G930V using Tapatalk
  12. E

    Box Grader Vs Box Blade

    I bought a box blade for my gravel driveway and am very disappointed in either my skills or it being to small to work right and I really wish I would have gotten a box grader or land plane Sent from my SM-G930V using Tapatalk
  13. E

    Bx2670 glow plugs

    Thanks both of you for the clarification I guess I haven't ever started it with the glow plugs! No wonder it doesn't like to start terribly well when it's cold! Thanks all for the help!
  14. E

    Bx2670 glow plugs

    That is kind of what I thought. Thanks...one more question if I may..does it help when really cold to do run thru 2 cycles before starting? When I plug it in this isn't an issue it's just when starting when I don't get it plugged in. Thanks Sent from my SM-G930V using Tapatalk
  15. E

    Bx2670 glow plugs

    When turning the switch to the on position the glow plug light shows for around 5 seconds then goes off. Do the glow plugs also turn off when the light goes out or do they continue to run? Thanks in advance Sent from my SM-G930V using Tapatalk
See more
Top Bottom